Can the Power Grip RV Power Maximizer # CAM55025 Be Used with Three Generators

Question

Question:

Since I have 2 Honda eu2000i paralleled together and am now getting a 3rd one of the same size and kind, I am wondering if I could have plug the 30 amp side into my parallel kit and the 15 amp side unit my 3rd generators 110v socket since it is not gfi. I then can hook to my 50 amp chord on the fifth wheel. Your thoughts? Thanks,

asked by: Mark P

1

Helpful Expert Reply:

Yes, the adapter part # CAM55025 will work well for your application.

The 30 amp side can go to your paralleled generators and then the 15 amp to the third one giving you a 50 amp female socket.

expert reply by: Jameson C

1

Answer 1

I reached out to Camco about the Power Grip RV Power Maximizer - 50 Amp Female to 15 Amp Male and 30 Amp Male item #CAM55025 and received this information from one of their reps. All Grounds, “G”, and all Neutrals, “W”, are connected and they should…

view full answer...

Answer 2

Since the 15 amp plug and 30 amp plug both feed into the single 50 amp plug on Power Grip RV Power Maximizer #CAM55025 you would want both the 15 and 30 amp connections to both be single phase or 3 phase, whatever it happens to be. I suspect that if…

view full answer...

Answer 3

The Power Grip RV Power Maximizer #CAM55025 will hook up to your RV's 50 amp power cord and allow you to pull from a 30 amp power source and 15 amp power source at the same time for a combined 45 amps. You'll be able to plug the 15 amp plug…

view full answer...

Answer 4

You do NOT have to plug in both the 15-amp and 30-amp male ends to use the Power Grip RV Power Maximizer #CAM55025. You can plug in just the 15-amp or just the 30-amp male end and it will still work. The 30 or 15 amp end not plugged in will NOT be…

view full answer...

Answer 5

Are there any breakers or switching on your 2019 Reflection by Grand design 5th wheel that need to be switched on? A lot of cmapers will have master switches to shut off all power which you might check for on your camper.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 9

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 10

For a replacement you need the Titan Zinc-Plated Brake Actuator #T2477600. This is the Titan Model 10 which is the same as the Dexter DX12.5 you currently have on your boat trailer.

view full answer...

Answer 11

Hi Jeremy; that's a good question and you'll actually need to go ahead and re-do the set up of your weight distribution system after adding the Timbren Rear Suspension Enhancement System #TDR1500DS to your 2019 Ram 1500. So it wouldn't…

view full answer...

Answer 12

For your 2010 Forest River R-Pod 172 that has 3,500 lb Lippert torsion axles the correct lift kit is the #LC382741 that you referenced which will give you a 3-1/2 inch lift.

view full answer...

Can the Power Grip RV Power Maximizer # CAM55025 Be Used with Three Generators

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching