Hitch Recommendation for a 2001 Ford Ranger with a Flareside Bed
Question:
Will this hitch fit a 2001 Ford Ranger flareside?
asked by: Connor
Expert Reply:
Yes, the Draw-Tite Max-Frame, part # 75082, will fit your 2001 Ford Ranger Flareside. I attached installation instructions and an installation video of this product below for you to check out.
You may be interested in the following products to complete your towing setup:
T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, part # 118344
Ball Mount 3/4 inch Rise or 2 inch Drop, part # AMSC2
Hitch Ball with 2 inch Diameter and Medium Shank, part # 19247
Hitch Ball with 1-7/8 inch Diameter and Medium Shank, part # 19260
Pin and Clip, part # PC3
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Matte Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Shock Absorbing
- Convert-A-Ball
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Does Draw-Tite Trailer Hitch 13091 Require Drilling to Install on 2001 Ford Ranger
- Q&A: Recommended Hitch for a 2024 Subaru Outback
- Article: Which Hitches are Made in the USA
- Q&A: Will The etrailer Trailer Hitch Receiver Fit With Larger Spare Tire On 2021 Ford Ranger Tremor?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Q&A: 2018 Nissan Murano Recommended Parts for Towing a Small Trailer
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Hitch and Wiring for 2024 Nissan Frontier