Will Regulator part # 108221 Fit Standard Low Pressure Propane Applications

Question

Question:

I want to hook up an LP gas range to a propane tank in our garage to use for canning this summer. I do not plan to use it year round. Which regulator and hoses do I need? Also what connections? Thanks,

asked by: Debra H

0

Expert Reply:

As long as your propane tank is a low pressure application the regulator part # 108221 would be the correct regulator to use as it regulates to the standard 11 inch water column.

The hoses and fittings needed would be based on the application though. I'd need more info on the appliance and hose length needed.

If you aren't sure what fittings you'd need you can send me pictures.

expert reply by: Jameson C

0

Answer 1

The inlet side of the MB Sturgis Horizontal 2-Stage Propane Regulator #108221 that you referenced is the larger end with the black top and the outlet is the bottom side. Basically it needs to mount pointing down like the picture I attached.

view full answer...

Answer 2

The Horizontal Low Pressure 2-Stage RV LP Gas Regulator #37207-30385 does have mounting holes that are 3-1/2" center on center. We do not carry the MEGR-298 MEC regulator so I am not familiar with it. But from what I could find on it, the…

view full answer...

Answer 3

Those three regulators are all very similar and essentially do the same thing but they're used on different propane setups. Part #37207-30365 is a vertical regulator. Vertical regulators are commonly on propane systems on travel trailers or pop…

view full answer...

Answer 4

The MB Sturgis Propane Pigtail - Stainless Overbraid - Type 1 x 1/4" Male Inverted Flare - 15" #100833-15 is an 1/4" inverted flare tip and your regulator requires a standard 1/4" NPT fitting. You just need a pigtail like Propane…

view full answer...

Answer 5

For your 30,000 BTU wall mounted heater you will need to use a dual-stage propane regulator. The correct regulator will be the MB Sturgis Vertical 2-Stage Propane Regulator - 11" Water Column Outlet #108220. You will need a vertical regulator if…

view full answer...

Answer 6

We don't sell the 3/4 x 5-1/2 inch grade 5 bolts needed to lock out a Sidewinder. The only way you will be able to get the correct bolts would be to go to your local hardware store and get them there. This will save you time as you won't have…

view full answer...

Answer 7

Since you are looking to lock-out your Sidewinder pin box #RP34FR, the bolts you need to add are at the rear through the rotating turret and the base. Then the wedge you need to remove is on the underside near the king pin. You simply remove the two…

view full answer...

Answer 8

We do have a potential option for you. While we do not carry a direct replacement for the Champion part 100157213 that you mentioned, we do carry a very similar 2-stage regulator with the MB Sturgis Horizontal 2-Stage Propane Regulator #108221. This…

view full answer...

Answer 9

For a single tank setup the regulator you would want is the part #108220 which is rated for 400,000 btus. The regulator you mentioned does not have enough BTU.

view full answer...

Answer 10

It sounds like your propane regulator is bad and needs to be replaced. These are not repairable which is why you need to replace yours and it's pretty easy to do. I see you were looking at a dual stage regulator so if that is what you have then…

view full answer...

Answer 11

All of the RV regulators we carry are going to work down the output pressure to 11" water column. That pressure will always stay the same but the amount of BTU's you can spread between the appliances can vary depending on the regulator. For…

view full answer...

Will Regulator part # 108221 Fit Standard Low Pressure Propane Applications

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching