Recommending a Hub Assembly for a 4 x 8 Trailer
Question:
I need a replacement hub assembly and I cant figure out which one will fit on my axle spindle. The bolt pattern is 5 on 4.5, the axle is 60 inches from hub face and 48 inches from spring center. The bearings are L44643. The spindle is 4-1/16 inches long, and I measured 63/64 inch diameter the entire length, threaded at the end. I measured the castle nut just to make sure and the inside dimensions of the castle nut are 1 inch. The existing hubs seem like cast iron, very heavy, and the trailer came with 12 inch tires but I would like to switch to 8 inch because it is a little trailer, only 4 x 8. I'm interested in an entire assembly, as easy to install as possible, preferably galvanized since the trailer sits outside. Thank you very much for your help.
asked by: Tye J
Expert Reply:
Thank you for taking the time to make all those measurements, it is a big help. Based on the info you provided, you will need the Trailer Idler Hub Assembly for 2,000-lb Axles # AKIHUB-545-2-G-1K. This assembly has a galvanized finish and can fit 8 inch to 12 inch wheels to accommodate your 4 x 8 trailer.
Since you would like to switch to a smaller wheel and tire, I recommend taking a look at the Kenda 5.70-8 Bias Trailer Tire with 8" Galvanized Wheel # AM30110. The 8-inch wheel fits your 5 on 4-1/2 bolt pattern, and has a maximum load capacity of 715 lbs at 50 psi per tire, which should be more than enough for your 4 x 8 trailer.
I have included links to a pair of video reviews about these products for you to take a look at.
![Kyle S](https://images.etrailer.com/static/images/catg/people/1237_tn.jpg)
Products Referenced in This Question
Kenda 5.70-8 Bias Trailer Tire with 8" Galvanized Wheel - 5 on 4-1/2 - Load Range B
- Trailer Tires and Wheels
- Tire with Wheel
- Bias Ply Tire
- Load Range B
- 5.70-8
- 8 Inch
- 5 on 4-1/2 Inch
- Steel Wheels - Galvanized
- Boat Trailer Wheels
- Kenda
more information >
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Standard
- L44643
- L44643
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Q&A: How To Choose Correct Replacement Hubs for 2005 Wesco Boat Trailer
- Q&A: Can Trailer Hub AKIHUB-545-2-G-1K Replace Hub that Used Wheel Bolts
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Video: Kenda Tires and Wheels - Tire with Wheel - AM30110 Review
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Q&A: How to Tell if a Trailer Spindle is Damaged or Needs to be Replaced
- Search Results: spindle
- Search Results: l44643
- Search Results: bt8 hub
- Search Results: grease
- Search Results: bt8 1" spindle
- Search Results: bearing buddy cap
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Shop: Roof Rack
- Shop: Trailer Hitch
- Q&A: Trailer Hitch to Fit a 2019 Mazda 3 Sedan
- Q&A: Hitch for 2016 Mazda 3 Hatchback to Carry 3 Bikes
- Search Results: trailer safety chains
- Q&A: Common Torque Specifications for Lug Nut Size
- Q&A: Should Tires Be Balanced When Installed on Dexstar Galvanized Wheel # AM20134