Can Mounting Studs be Removed from Hydraulic Brake Assemblies AKFBBRK-35-D

Question

Question:

Are the studs removable from the backing plate on the Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10inch - Left/Right Hand - 3,500 lbs Item # AKFBBRK-35-D

asked by: Bill

0

Expert Reply:

The four mounting studs on Hydraulic Brake assemblies # AKFBBRK-35-D are not removable. These are press-fit for a permanent installation. For a similar brake without studs you can use Demco kit # 40716-15. These brakes are also free-backing galvanized finish left- and right-hand brakes for 3500-lbs axles.

expert reply by: Adam R

0

Answer 1

Based on your description and measurements, this pair of fenders will make a great replacement. Typically you want to match the dimensions of your old fenders so at 60" long these will work well. They are also 9" wide and 12" tall.…

view full answer...

Answer 2

The Atwood Brake Actuator AT82543 referenced in your question is compatible with any trailer that has hydraulic drum brakes. Uni-servo wheel cylinders are found on certain hydraulic brake assemblies. If an assembly has them, this basically means that…

view full answer...

Answer 3

The Demco Hydraulic Brake Kit #40716-15 uses a 3/16" Inverted Flare fitting to connect to the brake lines. If you need new mounting hardware for your brakes you can use the Redline Kit for 10" Brake Assemblies #BRKH10A .

view full answer...

Answer 4

The big differences is basically pricing and brands. The part #AKFBBRK-35-D is a pair of Dacromet coated drum, hydraulic brakes that are free-backing. The part #40716-15 is essentially the same thing buy made by Demco. The etrailer brand is going to…

view full answer...

Answer 5

The Fulton trailer fenders part #F008584-2 would be a really great option for both sides of your Shoreland'r trailer that would closely match what came on it originally. To see if we have a cap or lid for your surge brake actuator will require…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Can Mounting Studs be Removed from Hydraulic Brake Assemblies AKFBBRK-35-D

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching