Ball Mount Recommendation for Use with a Draw-Tite # 75673 on a 2010 Subaru Outback Wagon
Question:
I have a 2010 subaru outback and want to install a hitch. I have not purchased a trailer as of yet 5x8 either. Everything is unknown, I am not show of the rise or required for the Ball mount. I question the clearance of 989900 ball mount and the bumper / trailer 8 inch on 75673 Draw-Tite to bumper - and 8 1/2 inch on ball mount center pin to ball? Is there enough clearance from the ball to bumper to slide the trailer over the ball if ball mount is used in raised position?
asked by: Bob
Expert Reply:
There is not a required ball mount for this Draw-Tite Trailer Hitch Receiver, part # 75673. Since you are worried about clearance I would recommend you use a Trailer Hitch Ball Mount, part # D-4. This ball mount has a distance of 10-1/4 inches from the center of the hitch pin hole to the ball hole. You would have plenty of clearance to run this ball mount in the rise position.
I attached installation instructions below as well as a review video of this hitch for you to check out.
Products Referenced in This Question
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Best Trailer Hitch Recommendation for 2017 Subaru Outback Wagon for Bike Rack and Towing
- Q&A: Trailer Hitch Recommendation for 2017 Subaru Outback Wagon for Carrying Bike Rack
- Q&A: Differences Between Curt, Draw-Tite, and etrailer.com Trailer Hitches for 2019 Subaru Outback Wagon
- Q&A: Do you Recommend the etrailer # e98847 or the Draw-Tite # 75673 for My 2018 Subaru Outback?
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Does Draw Tite Hitch # 75673 Fit on 2018 Subaru Outback Wagon
- Q&A: Hitch for 2011 Subaru Outback Wagon with Best Ground Clearance
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Hitch Installation Tips
Jameson C.
3/28/2011
There is not a required ball mount for this Draw-Tite Trailer Hitch Receiver, part # 75673. Since you are worried about clearance I would recommend you use a Trailer Hitch Ball Mount, part # D-4. This ball mount has a distance of 10-1/4 inches from the center of the hitch pin hole to the ball hole. You would have plenty of clearance to run this ball mount in the rise position. I attached installation instructions below as well as a review video of this hitch for you to check out.