How To Install The Optronics 6-1/2 Inch Oval LED Trailer Turn Signal and Parking Light # STL78AB
Question:
Since other cars cant see me signaling, I want to install these above the OEM cheap bulb tail/turn/brake. Those are flush mount, sitting in rubber gaskets no fastners, held by friction? and have 3 wires off the back: ground, tail, turn/brake. Do I need an adapter when I splice off these for the STL78AB, or will the wiring be obvious?
asked by: David B
Expert Reply:
The wiring on the Optronics Sealed, 6-1/2 Inch Oval LED Trailer Turn Signal and Parking Light, part # STL78AB, is three wires. It is white for ground, black for parking light function, and red for turn function. You will not need an adapter to connect these lights to your trailer.
These are surface mount lights that will attach to your trailer through the four mounting holes. The only other hole needed would be for the wires on the Optronics lights to go into for connection to your existing trailer light wires.
Product Page this Question was Asked From
Optronics LED Trailer Parking Light with Turn Function - Submersible - 10 Diodes - Oval - Amber Lens
- Trailer Lights
- Tail Lights
- Parking
- Turn
- Oval
- Surface Mount
- Submersible Lights
- LED Light
- 6-1/2L x 2W Inch
- Amber
- Optronics
more information >
Continue Researching
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 4 Bolt Flange - 2,000 lbs
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 2,000 lbs
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - No Drop - 4 Bolt Flange - 2,000 lbs
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Optronics LED Mini Clearance or Side Marker Trailer Light - Submersible - 2 Diodes - Amber Lens
- Shop: Kenda Karrier ST205/75R14 Radial Trailer Tire with 14" Black Mod Wheel - 5 on 4-1/2 - LR C
- Search Results: grease seal 10~9
- Search Results: 10~19
- Search Results: hitch stabilizer
- Search Results: trailer tongue extension
- Q&A: Could A-Frame Trailer Coupler # CA-5100-Z be Bolted On
- Q&A: What Is Needed to Install Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball
- Q&A: Mounting Hole Diameter on the Titan Coupler T2343400
- Q&A: What Size Bolt Holes Does etrailer Coupler # CT-2003-Z Have
- Q&A: Correct Idler Hub For Timbren Axle-Less Trailer Suspension # ASR2000S02, 5 on 4.5 Inch Bolt Pattern
- Q&A: 15k BTU AC Unit to Replace Dometic Duotherm 630035.321 RV AC Unit
- Q&A: Comparing Fulton F2 and XLT Winches
- Article: Trailer Maintenance Schedule
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Lighting Requirements
- Article: Basics of Tie-Down Anchors