Parts Needed to Tow a Trailer with a 2008 Honda Odyssey
Question:
Hi there, Do you have packages for a 2008 honda odyssey. Looking for a hitch, ball-mount and wiring kit
asked by: Mike
Expert Reply:
We don't have complete towing packages for vehicles but I can recommend the parts you'll need to tow a trailer with your 2008 Honda Odyssey.
I recommend the Draw-Tite Trailer Hitch Receiver # 75270. It's a 2 inch, Class III hitch that's custom designed for your van. I suggest the Class III hitch because it will have higher ratings and be more compatible with accessories.
Then the wiring harness # 118438 will provide you with a 4-way trailer connector. It plugs into a connector located behind a trim panel on the passenger's side in the rear cargo area. It also includes a fuse that you'll insert into your fuse panel.
You'll also need a ball mount and hitch ball. I've attached a link of our selection of ball mounts for a 2 inch hitch receiver as well as an article to help you determine the correct rise or drop you may need. Once you choose a ball mount you can then choose a hitch ball to fit it.
One way to make choosing a ball mount easier is to go with an adjustable ball mount like the B&W Tow & Stow # BWTS10038B. It features the ability to be flipped under the hitch when not using it and will provide up to 5-1/2 inches of rise or 5 inches of drop.
For a pin and clip to fit you can use # PC3 or if you'd like to have a locking pin you can use # BX8858.
I've also included links to some articles on towing that you might find helpful.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 7.5K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Matte Black
- Drop - 5 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class IV
- B and W
more information >
Blue Ox Trailer Hitch Receiver Lock for 2" Hitches
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Unique
- Fits 2 Inch Hitch
- Flush Pin
- 2-3/4 Inch Span
- Blue Ox
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Recommended Hitch for VelociRAX 5 Bike Rack on 2012 Honda Odyssey
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Comparison Between Draw-Tite 76025 and EcoHitch 306-X7253 for 2015 Honda Odyssey
- Article: Trailer Wiring Diagrams
- Article: Transmission Cooler
- Q&A: Choosing OEM or Aftermarket 5th Wheel Puck System for 2021 Ford F-250
- Q&A: How To Install a 7-Way Trailer Connector On a 2016 Honda Odyssey
- Q&A: Honda Odyssey Custom Built Class III Round Tube Trailer Hitch Bolt Sizes
- Q&A: Solution for Keeping RV Furrion Refrigerator Doors Closed when Travelling