What Tools are Needed to Install the Draw-Tite Hitch # C11041 on a 2001 Ford Mustang
Question:
how to install it what do i need and how long is it
asked by: Alex
Expert Reply:
If you have average mechanical abilities and basic tools this Curt, part # C11041, would take about 40 minutes to install on your 2001 Ford Mustang.
I attached installation instructions below that detail exactly how the # C11041 will install on your Mustang, there are also many useful diagrams that show how it all comes together too.
You will need the following tools:
13 mm wrench, 15 mm wrench, 11/16 inch wrench, torque wrench, a drill with a 1/4 inch drill bit, 7/16 inch drill bit, and a 1 inch hole saw.
You may be interested in purchasing the following:
Sportframe Drawbar 2-1/8 inch Rise or 2-3/4 inch drop, part # 3592
Hitch Ball with 2 inch Diameter and Short Shank, part # 19258
Hitch Ball with 1-7/8 inch Diameter and Short Shank, part # 19256
Curt T-Connector # C55326
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Rooftop Cargo Carriers
- Q&A: Does Draw Tite Hitch for 2017 Ford Mustang Require Rear Fascia Trimming
- Q&A: Trailer Hitch and Wiring for a 2001 Ford Mustang
- Q&A: Tow Ready Wiring # 119176KIT Recommendation for a 2004 Mercury Grand Marquis
- Q&A: 2018 Mustang GT Trailer Hitch Recommendation
- Q&A: Replacement Trailer Taillight Lens for Part Number AS2T216
- Q&A: Lens Replacement for Trailer Taillight with SAE Number AS2T216
- Q&A: Bearings For Older Trailer Hub 22834
- Article: Where to Position the Trailer Axle?