Installation Of Draw-Tite Class I 1-1/4 Inch Hitch # 24867 On A 2011 Nissan JUKE
Question:
How easy this to put on is, is there any cutting of plastic bumpers, drilling needed, does it hang below the rear bumper? Do you have a photo of one on a Juke?
asked by: Gordon N
Expert Reply:
The Draw-Tite Class I 1-1/4 Inch Hitch, part # 24867, will fit your 2011 Nissan JUKE if it is an all-wheel drive (AWD) model. If you have the front-wheel drive (FWD) version of the 2011 Nissan JUKE, I recommend the CURT Class I 1-1/4 Inch Hitch, part # C11302.
There is no drilling or cutting required when installing the Hidden Hitch. It will be located under the rear fascia. You will, however, need to remove the factory tow hook and fasteners at the rear of the vehicle. I am including a link to the installation instructions on the Hidden Hitch. I do not currently have a picture of the hitch on a Nissan JUKE
The Draw-Tite, part # 24867, will need the Draw-Tite Ball Mount, part # 3593. Also, for towing you would need the Tow Ready 2 Inch Hitch Ball, part # 19258, or Tow Ready 1-7/8 Inch Hitch Ball, part # 19256, and the Curt T-Connector Wiring Harness, part # C56124. I am including a link to the instructions for the Curt wiring harness.
If you will be towing with this hitch, you will want to check your owners manual or the Nissan dealer for the towing capacity of your 2011 Nissan JUKE AWD.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: Options For Replacing A Tie Down Turbo Lube 48394 Clear Oil Bath Cap
- Q&A: No Power at 12 Volt Pin In 7-Way on a 2008 Toyota Tundra
- Article: How to Measure for Trailer Hitch Drop
- Q&A: 2013 Nissan Juke Trailer Hitch Recommendation for Cargo Carrier
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Anti-Rattle Device Recommendations for 1-1/4 inch to 2 inch Hitch Adapter
- Q&A: Does the Pro Series Anti-Rattle Device Fit Both 1-1/4 and 2 inch Hitches
- Q&A: Electric Fat Tire Bike Rack Recommendation for 1-1/4 inch Hitch
- Q&A: Can Hanging Bike Rack with Adapter Bar Be Used with 80 Lb E-Bike
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Hitch Receiver Sizes