How Much Power will SuperChips FlashPaq F5 Programmer Give 2011 Ford F-250 Diesel

Question

Question:

I have been trying to find the approximate horsepower and torque gains for installing the Superchips F5 Flashpaq in a 2011 F250 with the 6.7 liter diesel

asked by: John G

0

Expert Reply:

The Superchips F5 programmer part # SU1845 that you referenced is a confirmed fit for your 2011 Ford F-250 diesel and has been dyno tested to give the truck up to an additional 157 horsepower and 180 ft lbs of torque.

expert reply by: Jameson C

0

Answer 1

I recommend the Edge Diesel Evolution CTS3 Performance Tuner #EP96TR for your 2016 Ford F-250 with the 6.7L diesel engine. This tuner allows you to easily switch from different power levels based on your situation. There is a daily driver(improve…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

How Much Power will SuperChips FlashPaq F5 Programmer Give 2011 Ford F-250 Diesel

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching