Ball Mount Recommendation for 2016 Ford F-150 Towing Casita Travel Trailer
Question:
We just purchased a 2016 Ford F-150 to replace an older TV for our Casita Travel Trailer. I need to purchase a Class III ball mount and a sway bar attachment. Using your measurement instructions, I calculate that the F-150 receiver is about .875inch higher than the Casita coupler. If I purchase the items I have listed below, Im estimating that I will get about a 1.625inch , for a difference of about .75inch with the Casita being lower than the F-150. Would you please confirm, and also double-check to make sure I have the correct parts? Thanks so much! RP26003 Reese Sway-Control Bracket for 2inch Ball Mounts - Class III and IV - RP26003 C40093 Curt Sway Control Hitch Ball - C40093 AMSC2 Ball Mount 3/4inch Rise or 2inch Drop, 7,500 lbs - AMSC2 C40020 Hitch Ball with 2inch Diameter and Long Shank - 6,000 lbs Chrome - C40020
asked by: Susan P
Helpful Expert Reply:
Everything looks good! The Ball Mount part # AMSC2 will work well for you and gets you close enough to level that the trailer would tow fine. The hitch ball part # C40020 will fit the ball mount, the bracket part # RP26003 fits the ball mount, and the ball # C40093 will fit that.
You didn't mention a sway control unit though. For that the part # 83660 would work great. It comes with the smaller hitch ball as well.
Products Referenced in This Question
Reese Friction Sway Control Kit - Economy - by Draw-Tite, Reese and Hidden Hitch
- Accessories and Parts
- Weight Distribution Hitch
- Sway Control Parts
- Reese
more information >
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Matte Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Shock Absorbing
- Convert-A-Ball
more information >
2" Hitch Ball - 1" Diameter x 3" Long Shank - Chrome - 6,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 3 Inch Shank Length
- 1 Inch Diameter Shank
- 6000 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Reese Sway-Control Bracket for 2" Ball Mounts - Class III and IV
- Accessories and Parts
- Weight Distribution Hitch
- Adapters
- Sway Control Parts
- Brackets
- Reese
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Trimax Trailer Wheel Chock and Lock for 175/80R/13 Tires
- Article: How to Measure for Trailer Hitch Drop
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Q&A: Parts Needed to Add Brake Controller to 2024 Toyota Sienna Platinum
- Article: RV Roof Types: What Type of Roof Does My RV Have?
- Q&A: Can The Furrion Vision S Prewired System Be Switched to Us Voyager WiSight Camera System?
- Article: Steel vs. Aluminum Ball Mounts
- Q&A: Recommended Sway Control for 1800 lbs 13 Foot Scamp Travel Trailer
- Q&A: Can Sway Control be Used on a Trailer without Using Weight Distribution
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Replacement Motor For A Thompson Saginaw Part No. 7831293
- Q&A: How to Determine if a Vehicle has a Class I or Class II Trailer Hitch
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?