Recommended Trailer Hitch and Wiring for 2016 Toyota Sienna
Question:
Could you verify that the Curt C13105 hitch and the Curt t-connector C56106 wiring harness will fit the subject vehicle?
asked by: Don
Expert Reply:
The Curt Class III Trailer Hitch Receiver # C13105 referenced in your question is confirmed to fit your 2016 Toyota Sienna. This 2 inch trailer hitch receiver has a tongue weight capacity of 350 pounds and a gross trailer weight capacity of 3,500 pounds. It is custom fit for your vehicle, so there will be no drilling required during installation.
I have attached an installation video on your vehicle for you to check out.
The Curt T-Connector Vehicle Wiring Harness # C56106 also mentioned in your question will fit your vehicle as long as it is the SE model. If your Toyota Sienna is not the SE model, you will instead use the Curt # C56261. These will quickly and easily install a 4-way trailer connector on your vehicle by plugging directly into existing wiring.
If you also need a ball mount for towing your trailer, I recommend the Curt Ball Mount # C45230 that has a 2-3/8 inch rise or a 3-5/8 inch drop. I have also attached a link that will take you to our available ball mounts as well as a helpful article that explains how to choose the right one for your setup.
Products Referenced in This Question
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Comparing Curt and etrailer Hitch for 2023 Toyota Sienna
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Dimensions of C-Channel for Enclosed Trailer # 362213-955
- Q&A: Differences Between Curt, Draw-Tite, and etrailer.com Trailer Hitches for 2019 Subaru Outback Wagon
- Q&A: Tongue Weight Rating of 2016 Toyota Sienna When Using the Draw-Tite Max-Frame # 76112 Trailer Hitch
- Q&A: Best Trailer Hitch Receiver for Ground Clearance to Fit a 2013 Toyota Sienna
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit
- Article: Rust Prevention
- Article: Best Bike Racks for Electric Bikes
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch