Recommended Higher Capacity Spring Bars And Head For Equali-zer Weight Distribution System

Question

Question:

I purchased a equalizer WDhitch from you a couple years ago. It is a 90-00-0600, 600lbs tongue weight. I am buying a new trailer 6000lbs empty 670lbs tongue, 10,000 full. Can I purchase heavier bars that will work with my existing system?

asked by: Mike K

1

Helpful Expert Reply:

Yes. To upgrade your 600 lb Equal-i-zer weight distribution system to a higher capacity, you will need to replace your spring bars, but also the head. I recommend the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,200 lbs TW # EQ90-01-1299 for this application along with the Replacement Head for Equal-i-zer Weight Distribution Systems - 1,200 lbs TW # EQ90-02-1200. It is an easy change out of your spring bars and head and you won't need to buy an entirely new system. You may need to change out your hitch ball depending on your coupler compatibility.

expert reply by: Jason S

1

Answer 1

Since the 1,200 Equal-i-Zer spring bars #EQ90-01-1299 are wider at 1-1/2 inches than the 1,000 lb bars which are 1-3/8 inch you'd have to swap heads too. So with that you'd need the part #EQ90-02-1200 too to be able to convert from 1,000 lb…

view full answer...

Answer 2

The benefits of an Equal-I-zer hitch over the e2 is primarily the improved 4-point sway control of the Equal-I-zer. The 4-point sway control utilizes steel on steel friction at the arms as well as in the hitch head to stop sway. The e2's 2-point…

view full answer...

Answer 3

I'm not sure how to find out the age of your setup, but when I passed your photos along to my contact at Equal-i-zer he said that all you need to do for the upgraded system is swap out your 12K head unit for the 14K #EQ90-02-1400. Since your…

view full answer...

Answer 4

The ladders that are found on the backs of RVs and travel trailers are fairly universal, and not necessarily specific to your coach. These ladders can be trimmed to size but come in 3 basic ladder heights: 84-1/2-, 97- and 99-1/2-inches tall. You can…

view full answer...

Answer 5

I spoke my contact at Equal-i-zer and he told me that since it has 1 1/2" bars it is probably rated for 12,000 lbs. He said the way to tell for sure is to measure the bolt channel. If it measures 3/8" it is a 12,000 lb hitch, if it measures…

view full answer...

Answer 6

Weight distribution system bars like the Blue Ox Sway Pro #BXW4006 all work well over a range of loaded trailer tongue weight (TW). These particular bars are suited for a trailer with a loaded TW of 550 to 750-lbs. All Blue Ox bars are shown on the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...