Replacement Mounts For Thule Pull Top Slide-Out Ski And Snowboard Carrier

Question

Question:

I want to use the universal minting kit you guys have, but am unsure how to get the original mounts off my pull top ski rack. How do I remove the mounts/feet so I can use the new ones?

asked by: Margaux

0

Expert Reply:

To remove your old mounting brackets/feet, you will need to trace the bolt from the feet to the inside rail of your carrier. This will involve carefully removing components like the underside padding on your current mounts to access the bolt. Because you have the sliding carrier, It will be easy to see how one of the mounts disassembles removing a nut on the rail, but you will need to take the carrier off to remove the other nut covered by the sliding portion of the carrier.

I recommend using the Replacement Mounting Brackets and Hardware for Thule Pull Top Slide-Out Ski and Snowboard Carrier # TH753277902 if you only need the lower brackets, and the Mounting Kit for Thule Pull Top Rooftop Ski and Snowboard Racks # TH7520970001 is you need the full replacement.

expert reply by: Jason S

0

Answer 1

The Replacement Mounting Brackets and Hardware for Thule Pull Top Slide-Out Ski and Snowboard Carrier #TH753277902 will work if the holes are 4 inches apart on center.

view full answer...

Answer 2

Yes. The Yakima FatCat EVO 6 Ski and Snowboard Carrier #Y03096 will fit on any aero/elliptical aftermarket crossbar, including Thule Wing Bar Evo like the #TH711420.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I reached out to Thule and found that the difference between the Replacement 20 mm SpeedLink Mounting Hardware Assembly for Thule SnowPack Ski and Snowboard Carrier #7521241002 and the 13 mm #7521241001 is the length of that center bolt/screw. You…

view full answer...

Answer 6

Thank you for the information and the photos! According to what you sent in it looks like you have one of the discontinued Thule Flat Top (TH91724 or TH91725) or Pull Top (TH91726) carriers. These came with universal mounting hardware as well as an…

view full answer...

Answer 7

The Thule Hullavator Pro Kayak Carrier #TH898 is only compatible with the Yakima CoreBar crossbars if you also use the mounting kit #TH7520970001. Just be sure that you have the proper clearance (4" - 8" beyond the feet) for this to work…

view full answer...

Answer 8

The Mounting Kit #TH7520970001 For The Thule Pull Top ski rack will fit your roof rack crossbars. This mounting kit was designed to fit the Wingbar Evo crossbars which are the same 3.14" x 1" as your current crossbars.

view full answer...

Answer 9

The Replacement SpeedLink Mounting Hardware Assembly for Thule SnowPack Ski and Snowboard Carriers #7521241001 or the Mounting Kit for Thule Pull Top Rooftop Ski and Snowboard Racks #TH7520970001 will be compatible with the aero style bar. Either of…

view full answer...

Answer 10

To determine which Thule replacement hardware you'd need we have to know which Pull Top you have. The part #7533998 is for the TH725 and the part #TH7520970001 is for the TH726 both of which are discontinued. Since you said you also need the…

view full answer...

Answer 11

To mount the Thule 726 Pull Top Ski Carrier you will want the Mounting Kit for Thule Pull Top Rooftop Ski and Snowboard Racks item #TH7520970001. This mounting kit can fit crossbars up to 3-1/8 inches in width.

view full answer...