Will Draw-Tite Trailer Hitch Fit a 2012 Subaru Outback 3.6R with Rear Bumper Underguard
Question:
Subaru Outback 2012 3.6R Limited. Want to install Draw Tite part #75673. My car has an extra piece on the rear bumper called a bumper under guard. Its the light gray plastic add-on piece, purely decorative, shown in attached photo. It extends maybe an inch at maximum below the main bumper. I want to know if the hitch will clear this bumper underguard. I dont want to have to cut it.
asked by: Rob H
Expert Reply:
Yes, Draw-Tite trailer hitch # 75673 will fit your 2012 Subaru Outback 3.6R with that bumper under guard. I have included a picture from a customer that has the same piece on their bumper.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And for trailer wiring you can use # 118467 to add a 4-Way flat connector to the rear of the vehicle. I have also included some links showing example installations of the hitch and wiring for you.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: Recommended Tire Clearance Between Tires on Dual Axle Trailer
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Strut for Stabilus Lift-O-Mat on Dometic Awning
- Q&A: Is a Master Key Needed to Install or Remove a Thule Lock Cylinder
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Can Electric Trailer Brake Kit # AKEBRK-2 be Submerged in Water
- Q&A: Equalizer Replacement Options for Dexter 13-122 Equalizer
- Article: How to Choose the Right Trailer Hitch Class
- Article: My Trailer Hitch Doesn't Fit
- Article: Best Bike Racks for Electric Bikes
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)