Is Fascia Trimming and 7-Way Adapter Required for the 2009 Toyota Martix XRS with # 24812 Hitch
Question:
Watched video couple of times, did not see where facisa was cut away per advice from JeffD and earlier 2009 Matrix question submitted. Need to go to a 7pole round connector looks like adaper 30717 will work, right?.
asked by: Ron
Expert Reply:
I did some research and from what I can see on the 2009 Toyota Matrix the rear fascia is very similar on the S and XRS models. You may find that there is a part in the center of the fascia that needs to be removed on he XRS and XR Sort models, but no trimming is required, this part should snap out of the rear fascia, if your vehicle has it installed.
The Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector, item # 30717, can be added to your vehicle with the addition of the Tow Ready Custom Fit Vehicle Wiring for the 2009 Toyota Matrix, item # 118460. You could then wire tie the additional wires up out of the way. If you need the additional functions of the 7-Way connector, all of the wiring and connectors needed are included in the Brake Controller 7 & 4 Way Installation Kit, item # ETBC7. I have provided instructions for the installation of the 4-way and 7-Way connectors, and additional wiring for you along with helpful videos.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector
- Trailer Wiring
- Wiring Adapters
- Single-Function Adapter
- 0 - 5 Feet Long
- 4 Flat
- Plug and Lead
- 7 Round - Blade
- Tow Ready
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Recommended Flat Towing Components For A 2024 Chevy Trax
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: How to Choose the Right Trailer Hitch Class
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Roadmaster Tow Bar Feature Descriptions
- Article: Trailer Hitch Receiver Sizes
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Hitch for a 2024 Subaru Legacy
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Which Way Do the Washers Install On the Curt Hitch C12228
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Q&A: Is A 2 Inch Trailer Hitch Available For A 2009 Toyota Camry
- Q&A: Parts Needed to Tow Trailer with 2007 Toyota Matrix