Recommended Trailer Hitch Receiver to Fit 2017 Jeep Wrangler Unlimited Rubicon Hard Rock Edition
Question:
Trailer hitch for 2017 Jeep Wrangler Unlimited Rubicon Hard Rock? I dont know if it takes the same ones as their standard bumper or not. Thanks!
asked by: Bob M
Expert Reply:
The factory bumper on your 2017 Jeep Wrangler Unlimited Rubicon Hard Rock Edition is the Mopar part # 82213654.
So the Draw-Tite Max-Frame # DT78MR is confirmed to fit your Jeep.
If you're going to be towing you'll also need a wiring harness. The Tekonsha # 118416 will work for you to provide a 4-way trailer connector. It plugs into the Jeep's wiring behind the driver's side tail light. I've attached a video of the install for you.
You may be interested in an adjustable ball mount like the B&W Tow & Stow # BWTS10035B. The Tow & Stow features the ability to be flipped under the hitch and out of the way when not towing. It also will provide up to either 3 inches of drop or 3-1/2 inches of rise. If that ball mount doesn't work for you I've linked our selection that will fit the Class III Draw-Tite as well as an article to help you determine the correct rise or drop you need.
For a pin and clip use # PC3 unless you'd rather a locking pin to secure the ball mount use # BX8858.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 3" Drop, 3-1/2" Rise - 7.5K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Matte Black
- Drop - 3 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class IV
- B and W
more information >
Blue Ox Trailer Hitch Receiver Lock for 2" Hitches
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Unique
- Fits 2 Inch Hitch
- Flush Pin
- 2-3/4 Inch Span
- Blue Ox
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 4500 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- No Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Best Bike Rack Out of Thule Epos, Hollywood Racks Destination, and Yakima OnRamp Bike Racks
- Article: How to Choose a Bike Rack for a Jeep Wrangler
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Can I Use The Draw-Tite DT78MR To Replace The Factory Hitch On A 2023 Jeep Wrangler 4XE
- Q&A: Supplemental Braking System for 2018 Jeep Wrangler JL with Spartan K2 Chassis with Safe Haul Air
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Trailer Hitch for a Grand Design Solitude
- Q&A: What are the Dimensions of the Draw-Tite Max-Frame Trailer Hitch Receiver # DT78MR
- Article: Best Bike Racks for Electric Bikes
- Article: How to Choose a Bike Rack That Will Clear a Rear Mounted Spare Tire or Bumper