Installation of Replacement Heat Shield For Firestone Ride-Rite Air Spring Kit

Question

Question:

Not sure how to install on my 2010 Sierra

asked by: Terrell J

0

Expert Reply:

The Replacement Heat Shield # F2135821004 for a Firestone Ride-Rite Air Spring Kit like # F2250 will install at the top of the passenger-side air bag as shown in the included diagram which is taken from the linked instructions. The heat shield will mount between the upper bracket and the air helper spring. You will need to bend the heat shield so it will fall halfway between the air helper spring and the closest point on the exhaust. Be sure that the heat shield will not contact any other
component as the suspension compresses.

expert reply by: Adam R

0

click to enlarge

Answer 1

I spoke with my contact at Firestone, who tells me that the frame bracket for your B and W Gooseneck hitch will not interfere with the installation or use of the Ride Rite #F2250 Air Helper Spring. The air bag will locate between the underside of the…

view full answer...

Answer 2

The #F2250 Ride Rite system needs a minimum of 5 and a maximum of 100 psi. The proper air pressure for towing your fifth wheel would depend solely on your personal preference. I'd start at about 50 psi, and make some test runs. Add or lower air…

view full answer...

Answer 3

The Firestone Ride-Rite Air Helper Springs #F2250 on your 2003 GMC Sierra can be manually adjusted between 5 PSI and 100 PSI. According to the installation manual, the Air Helper Springs will typically support about 50 pounds of load for each psi of…

view full answer...

Answer 4

We do carry the replacement parts you need for the Firestone Ride-Rite Air Helper Springs #F2550 on your 2000 Ford F-250. - Replacement Bail Clamp for Firestone Ride-Rite Air Helper Springs #F3077 - Replacement Heat Shield for Firestone Ride-Rite Air…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Installation of Replacement Heat Shield For Firestone Ride-Rite Air Spring Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching