Will Trailer Hitch Receiver from Honda CR-V Fit 2012 Toyota Camry
Question:
Will a drawtite 36520 fit a 2012 Toyota Camry as I have it left over from another car..?
asked by: Martin. B
Expert Reply:
The Draw-Tite Class II # 36520 is designed to fit a Honda CR-V from 2012-2016. Unfortunately, it will not fit your 2012 Toyota Camry. For your Camry you will need the Draw-Tite Class II # 36540.
For a 4-way trailer wiring harness the Tekonsha # 118405 is a plug in adapter that installs into the Camry's existing harness inside the trunk, behind the tail lights.
For a ball mount the Draw-Tite # 36071 will give you either 2-5/8 inch rise or 3-1/4 inch drop. It also includes the pin and clip and will fit 2 inch hitch ball # 19258, or 1-7/8 inch hitch call # 19256.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Trailer Wiring Harness Recommendation for a 1999 Isuzu NPR
- Q&A: Brake Controller Installation on 2016 Mercedes-Benz Sprinter
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Battery Life and Charging Time For The Linxup GPS AT3 Tracking Device
- Q&A: Trailer GPS Device for Trailer Installation
- Q&A: How Much is Monthly Service for Linxup GPS Tracking Device
- Article: How to Install E-Track in 3 Easy Steps
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Q&A: Installation of Slipper Spring with Open Eye End
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement Connector for a Pollak PA66-MD40
- Article: Best Vehicles to Flat Tow Behind an RV
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Article: Best Bike Racks for Electric Bikes