Recommended Method for Installing Erickson Adjustable Ratcheting Wheel Net with Hooks EM58522
Question:
I am looking to purchase the following product. Erickson Adjustable Ratcheting Wheel Net w/ Hooks - 4inch Wide - 3,333 lbs Code: EM58522. I have a flat bed car hauler. Can I use the side stake pockets for attachment? If not, I will purchase and install D rings on the trailer floor. How far apart do the D rings need to be per tire? How much in front of the tire and how far behind the tire. I assume that the ratchet will be in front of the front tires and the ratchet will be behind the rear tires to pull against each other, is that correct? Thanks.
asked by: Larry W
Helpful Expert Reply:
The Erickson Adjustable Ratcheting Wheel Net with Hooks # EM58522 can be attached to your trailer's stake pockets (presuming they offer enough strength for securing the weight of the car loaded on the trailer) but I still recommend installing a deck-mounted D-ring like Brophy's # RR5K. Their ideal placement will depend on your tire size. Once you have the nets you'll easily tell where to place the D-rings.
This assembly offers a 5000-lb load rating and features an anti-corrosive zinc plated finish. A backing plate for the underside of the deck for additional strength and the required mounting hardware are included. You will need two of the D-rings for each of the wheel nets.
It does not matter which side of the wheel net assembly, hook or ratchet, faces forward since each net will be pulling downward on the tire. The front and rear wheel nets do not pull against each other, only downward. You may also want to use an axle strap kit like # 08504-05 for an additional point of securement for the loaded car.
You can also refer to the linked help article for more on cargo control.
Products Referenced in This Question
Erickson Car Tie-Down Kit - Twisted Flat Hooks and Axle Strap w/ Ratchet - 3,300 lbs
- Car Tie Down Straps
- Snap Hooks
- 1 Strap
- 6 - 10 Feet Long
- Axle Strap
- 1-1/8 - 2 Inch Wide
- 2001 - 3500 lbs
- Erickson
more information >
Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 1600 lbs
- D-Ring
- Surface Mount - Bolt-On
- Brophy
more information >
Product Page this Question was Asked From
Erickson Adjustable Ratcheting Wheel Net w/ Hooks - 4" Wide - 3,333 lbs
- Car Tie Down Straps
- 1 Strap
- Wheel Net
- 2001 - 3500 lbs
- Erickson
more information >
Continue Researching
- Q&A: Slipper Spring Hanger Positioning for 7,000 lb Tandem Axle
- Q&A: Recommended Tie Down Strap for a 2010 Jeep Wrangler With 35" Tires
- Q&A: How Long Is the Strap With the Hook on the Erickson Adjustable Ratcheting Wheel Net EM58522
- Q&A: How Much Will The Durabilt Ratchet Chain Binder # DU32MR Close Up?
- Q&A: Frame Mounted Forged D-Ring Tie Downs on Big Tex 70 Steel Car Trailer
- Q&A: Recommended 5th Wheel Hitch for a 2024 GMC Sierra 2500 w/ Towing Prep Package
- Q&A: Wheel Straps to Tie Down a Polaris Range EV
- Article: Slipper Spring Trailer Suspension System Review
- Article: How to Install E-Track in 3 Easy Steps
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: How to Measure for Trailer Hitch Drop
- Article: What To Look For When Buying Ratchet Straps
- Article: Trailer Maintenance Schedule
- Article: How to Replace an RV Roof Vent Cover