What Screw is Used with the Operator part # BV0115-04

Question

Question:

What size is the knob screw

asked by: Dennis W

0

Expert Reply:

The screw that comes with the operator is part # V0423-01 which is a 8-32 x 3/4 inch machine screw.

expert reply by: Jameson C

0

Answer 1

The ball diameter on the Replacement Suction Cup Mount for Furrion Vision S 5" and 7" Monitors #FR79SR is .85". I have attached a product overview video as well as a diagram for you to check out as well.

view full answer...

Answer 2

I recommend the Bauer Products European Style RV Entry Door Lock #BA38AR to replace your Bargman L400. As there is not a direct bolt on replacement for the Bargman L400 you will need to fabricate a panel to cover the larger hole on your door and…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

To replace your Atwood RV Water Heater, Model #GC10A-4E, the direct replacement is the Atwood RV Water Heater - Gas and Electric - part #AT94022. This is the new version of your existing water heater, so it will have all the same features like a…

view full answer...

What Screw is Used with the Operator part # BV0115-04

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching