What Size Nut Fits on Replacement Stainless Steel T-bolt 853-5648

Question

Question:

I see the measurements of this bolt expressed as a mix of metric and SAE units. Can you tell me what actual metric nut size is required to mate with these T bolts?

asked by: Ron

0

Expert Reply:

The 1.5x22mm is actually a common designation. The 1.5 is 1.5mm and is referring to the pitch. The 22 is 22mm and is the length of the threaded part. The diameter is 3/8 but since it is metric that would equate to 10mm. So you would need a 10mm nut that has a pitch of 1.5mm.

expert reply by: Michael H

0

Answer 1

Yes, the Replacement Stainless Steel T-bolt #853-5648 that you referenced will fit the channel slot on the top of your Thule Aeroblade bars.

view full answer...

Answer 2

It looks like you have the Thule Aeroblade bar. The T-slot dimensions are 1/2 inch wide for the top of the opening and 3/4 inch wide at the bottom. The T-slot is 1/8" inch tall.

view full answer...

Answer 3

The T-bolts for Yakima Jetstream bars are one of the following; the Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers - Qty 4 #Y8880184, or the Replacement Long Mounting Bolts for Yakima MegaWarrior and LoadWarriorCargo Baskets #Y8870068.…

view full answer...

Answer 4

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 5

Malone AirFlow roof racks like #MPG215 can use their own T-Slot Fit Kit #MPG8287 for Malone carriers or you can use another T-bolt fastener. I linked a photo showing a cross section of the AirFlow bar and the exact inside dimensions. I converted the…

view full answer...

Answer 6

Yes, you can use the 50" Yakima JetStream bars part #Y00425 on the 2020 Kia Telluride LX with a naked roof. The 60" bars part #Y00426 are recommended by Yakima but it is possible to use the 50" bars if you would like to. I do agree…

view full answer...

Answer 7

Yes, the Yakima JetStream Crossbars Aluminum - Black - 50" Long - Qty 2, part #Y00425, will come with the necessary hardware to mount to the Yakima Timberline Towers.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 11

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Size Nut Fits on Replacement Stainless Steel T-bolt 853-5648

Product Page this Question was Asked From

Continue Researching