How To Install A Tekonsha Prodigy Brake Controller On A 2001 Nissan Frontier Crew Cab
Question:
We just bought a 6x10 utility trailer with 1 axle electric brakes. How do I tell if this unit (90185) will just plug right into my vehicle? Is there a place to look at pictures of the wires? I am handy, but I really don't want to run a long cable under the truck if I don't have to!
asked by: Jim H
Expert Reply:
Your 2001 Nissan Frontier Crew Cab is not wired at the dash for a plug in brake controller wire harness, but you will still be able to install the Tekonsha Prodigy Brake Controller. It will require that a wire be run from the rear of the vehicle to the engine compartment and a wire from the rear to under the dash to connect to the brake controller, but if you are handy it would be a pretty simple installation.
You will have to hardwire the Tekonsha Prodigy Brake Controller to your vehicle with the Brake Controller 7 & 4 Way Installation Kit, # ETBC7. It does require a 4-way trailer connector at the rear of your vehicle.
The # ETBC7 Installation Kit, comes with a new 7-Way and 4-Way connector which will plug into a 4-way trailer connector on the back of your vehicle. The 4 remaining wires will be hardwired to the vehicle. I am sending a link to detailed instructions on how to install the # ETBC7 kit on your vehicle.
If you do not have a 4-way trailer connector on the back of your vehicle you will need to use the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118362. This part will tap into the vehicles wiring harness located underneath the truck bed near the passenger side frame rail. There is no cutting or splicing of wires.
I am sending a link to a page with the instructions on a Tekonsha brake controller installation and the # 118362 wiring harness installation.
I am also sending a video link that will show the Tekonsha brake controller and ETBC7 kit being installed on a 2003 Chevrolet Express Van. The vehicle is different but the wiring principle is the same.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: Should I Get a Proportional or Time-Delayed Brake Controller
- Q&A: Parts Needed to Tow Trailer With Brakes Using 1992 Dodge D250
- Q&A: 4-Flat Trailer Wiring For 2024 Jeep Wrangler With Tow Bar Wiring