What Material is the Chrome Ring of the LED Utility Light # UCL60CB

Question

Question:

Is the chrome ring metal or plastic?

asked by: Scott

0

Expert Reply:

The chrome ring of the LED Utility Light # UCL60CB that you referenced is ABS plastic.

I attached a review video for this light for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I have a solution that may work for you, but we do not currently have any 3" diameter submersible reverse lights. Have a look at the Optronics Backup Light #BU45CB which is a 4-1/4" diameter light that can be mounted to your trailer using…

view full answer...

Answer 2

I do not recommend this but he most likely trimmed down the the clear plastic housing ring to fit the old trim ring over it. When installing the #UCL60CB you'll be fine just drilling new holes and using the two screw hole set up and using the…

view full answer...

Answer 3

I don't have an exact Kelvin Temperature rating of the Optronics LED RV Utility Light part #UCL60CB as it is not provided by the manufacturer but I do have a video of the light illuminated which you can see below. Based on said video, I would…

view full answer...

Answer 4

LED Utility Light #UCL60CB has a raw lumen output rating of 224 lumen. Raw output is the max output in ideal conditions. The effective lumen output, which is what you can count on the light producing, is 168 lumen.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

What Material is the Chrome Ring of the LED Utility Light # UCL60CB

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching