Replacement Tail Clamp for Trifecta Soft Cover Tonneau Cover

Question

Question:

Will the EX1035 tail clamp work on the Extang Trifecta Soft Tri-Fold covers? Mine looks just like this, but I cant find anything that says it will work on the soft covers. If not, can you please give me the correct part number to order?

asked by: Tara

0

Expert Reply:

Tail clamp # EX1035 does fit the Extang Trifecta Tonneau covers. But, if you have a 1999 or newer Ford Super Duty then you will instead need # EX1042.

expert reply by: Michael H

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

There might be a solution but it all comes down to what gooseneck hitch you have installed in your truck. If you can let me know what brand hitch you have I can help find you exactly what type of slider hitch solution would work best. Hopefully you…

view full answer...

Answer 4

Hey Trevor, so the B and W Companion Slider hitch part #BWRVK3400 only fits the B and W Turnoverball gooseneck hitches and would not fit the gooseneck hitch of your 2022 Chevy Silverado 2500 with OEM pucks. The funny thing about the Patriot slider is…

view full answer...

Answer 5

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 6

Hey Jim, congrats on the new truck and fifth wheel - looks great. Our rule of thumb is that you want a minimum of 6" of clearance between the top of the bed rails and the bottom of the trailer loft. You should be just fine to use the bottom hole…

view full answer...

Answer 7

The rear Timbren kit you'd want for your 2024 GMC Sierra 1500 is the part #T28MR which is the standard duty version. This will give you a better blend of support and ride quality than the severe duty version part #T53MR which would be a lot…

view full answer...

Answer 8

The Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers #EX1035 and front clamp #EX42FJ have a very basic design of a bolt with a nut on the end. You will remove the hinge cap or latch pocket cover from the cover and simply slide out…

view full answer...

Answer 9

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 10

I'm glad to hear that you received the Rear Tailgate Clamp, #EX31003005, for your Extang Trifecta 2.0 tonneau cover. I called Extang and discovered that they don't have any videos for replacing the rear clamp. But, they were kind enough to…

view full answer...

Answer 11

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold 2.0 Hard Tonneau Cover like #EX83651 you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need…

view full answer...

Answer 12

Yes, the part #EX1035 is the correct replacement tail clamp assembly for an Extang Solid Fold tonneau cover like what you have. I attached install instructions for this clamp for you to check out as well.

view full answer...

Replacement Tail Clamp for Trifecta Soft Cover Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching