What Gauge Wire Would be Required for Trailer with LED Clearance Lights that Draw 3.3 Amps
Question:
I am installing 42 clearance lights on a trailer that I just purchased from you, MCL13CA2B, MCL13CR2B, each light is 0.046 amp, also installing 4 STandT, STL89RCB, each light draws .350 on Turn and Stop, .022 on Tail, what size wire should I run for the LED lights? do you have a Chart? The trailer is 7ft. tall, 20ft. long, Enclosed, lights running top and bottom of trailer, thanks,
asked by: Ken O
Helpful Expert Reply:
Even thought that is a quite a few LED lights on your trailer the amount of amperage draw total for all circuit would be 3.35 amps. That's well below what standard lights would draw on trailers with just a handful of incandescent lights.
You would easily be able to get away with 14 gauge or even 16 gauge wire.
Products Referenced in This Question
LED Mini Clearance or Side Marker Trailer Light - Submersible - 2 Diodes - Red LEDs - Clear Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-1/16W Inch
- Red
- Optronics
more information >
Optronics Streamline LED Combination Trailer Tail Light - Submersible - 11 Diodes - Clear Lens
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail
- Oval
- Surface Mount
- Submersible Lights
- LED Light
- 17L x 1-1/2W Inch
- Red
- Optronics
more information >
Product Page this Question was Asked From
LED Trailer Mini Clearance or Side Marker Light - Submersible - 2 Diodes - Amber LEDs - Clear Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-1/16W Inch
- Amber
- Optronics
more information >
Continue Researching
- Shop: Trailer Wiring
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Q&A: Troubleshooting Trailer Lights Going Out When the Brakes are Applied After Trailer Light Kit Install
- Q&A: What Gauge Wire Should be Used to Wire 8 Marker Lights, Incandescent or LED
- Q&A: Wire Gauge Recommendation to Power 20 LED Trailer Clearance Lights
- Shop: Dragon's Eye LED Clearance or Side Marker Light - Weatherproof - Oval - 2 Diodes - Amber LEDs
- Video: Diamond Trailer Lights - Clearance Lights - DG52503VP Review
- Video: Pollak Wiring PK52249 Review
- Video: Review of Deka Wiring - 12-10 Gauge Butt Connectors - DW05745-10
- Q&A: How to Protect Circuit Breakers and Electrical Connections on a Trailer
- Q&A: Is the Bus Bar the Common Power Point on the Pollak 7-Circuit-Breaker Junction Box
- Shop: Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID
- Shop: Deka Heat Shrink Butt Connector - 16-14 Gauge - Nylon Insulation - Blue - Qty 10
- Q&A: What Gauge Wire does 4-Way Trailer Wiring Use
- Q&A: How To Turn Off The Tekonsha Prodigy P3 Brake Controller # 90195
- Shop: Roof Rack
- Search Results: rhino rack awning
- Video: Optronics Wiring - Trailer Connectors - A35W42B Review
- Search Results: 4 pin
- Search Results: trailer junction box
- Search Results: junction box
- Search Results: 7 pin junction boxes
- Search Results: 7 way junction box
- Search Results: junction
- Video: Review of Reese Weight Distribution Hitch - WD With Sway Control - RE94FR
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size