Trailer Wiring Recommendation for a 2002 Nissan Xterra
Question:
I have a 2002 Nissan Xterra and will be adding a trailer hitch to it. Which wiring do I use? Do I need to get under the vehicle to see if it has that connector shown in the video? Or the other one that I splice in? Thanks
asked by: Bill
Expert Reply:
If you get under the 2002 Nissan Xterra and find the connector that you see in the install video for the # 118244 you would need first test it with a circuit tester like part # PTW2993 to see if the pins are active when you apply turn signals on your Xterra. If so, then yes this kit would fit.
If not, you would need to hardwire with the part # 119178KIT.
The Draw Tite hitch part # 75107 that you referenced as well is the correct hitch for your vehicle.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with the right rise or drop to tow the trailer level, check out the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
Products Referenced in This Question
Tow Package Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - Nissan Xterra
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Tekonsha Tail Light Converter with 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 1-1/2 Feet Long
- Universal Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Tail Light Converter with 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 1-1/2 Feet Long
- Universal Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Install Video that Can be Used for 2007 Toyota Avalon for Trailer Wiring
- Q&A: Bulldog Powered-Drive Kit Compatibility With 12K Ram Landing Gear
- Q&A: Can the Bulldog Powered-Drive Kit be Used on Any Jack
- Q&A: Bypassing TIPM for Trailer Wiring Fix on 2004 Dodge Ram 1500
- Q&A: Replacement Bearings and Hub For 2007 EZ Loader Trailer Model With BT150A Oil Bath Hub
- Q&A: Adding a 7-Way Trailer Connector to a 2004 Dodge Ram with Factory 4-Way
- Q&A: Hasp Replacement for Enclosed Cargo Trailer Cam Door Lock
- Article: My Trailer Hitch Doesn't Fit
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller Installation: Starting from Scratch
- Article: Flat Towing Package for 2014-2018 Jeep Grand Cherokee
- Article: Routing the Power Wire for a Trailer Wiring Harness