Recommended Weight Distribution System for 2016 Keystone Travel Trailer With 7800 lb GVWR
Question:
morning I have a 2008 tundra towing a 2016 keystone travel trailer ,the hitch weight is said to be 710 with a GVWR OF 7800 lbs , I looking at purchasing the Strait-Line Weight Distribution w Sway Control - Trunnion Bar - 12,000 lbs GTW, 1,200 lbs TW RP66074 will this hitch be fine for my application
asked by: Mark M
Expert Reply:
To choose a weight distribution system, you'll need to first determine the fully loaded and ready to tow tongue weight of your trailer. To that figure, add the weight of any gear stowed in the cargo area of the SUV or truck bed behind the rear axle. I've linked to an FAQ article that explains how to do this. These combined figures represent the Total Tongue Weight (TTW) of your set-up. The TTW of your trailer should fall as close as possible to the middle of the effective range of the weight distribution system you choose.
You can't go wrong with the Strait-Line System, which actually stops trailer sway dead in its tracks before it can begin. I can recommend a few systems for you, but it'll be up to you to find the fully loaded trailer tongue weight of your trailer. The # RP66074 is designed for trailers with tongue weights between 600-1200 lbs. The next step up in capacity from there would be # RP66130, rated for tongue weights between 800-1500. Neither set-up includes the weight distributing shank, so you'll want to choose a shank that will place the trailer ball about 1-1/2 inches above level. I'll link you to an FAQ article that explains how to choose a ball mount that places the trailer level with the truck. The same principle applies to the weight distribution shank, you'll just want to remember to leave the trailer ball about 1-1/2 inches above level.
You'll also need a 2-5/16 inch trailer ball with a 1-1/4 inch diameter shank, like the # 19286.
Products Referenced in This Question
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 12,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-3/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 12000 lbs GTW
- Class IV
- Class V
- Draw-Tite
more information >
Strait-Line Weight Distribution w/ Sway Control - No Shank - Trunnion Bar - 15K GTW, 1,500 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Shank Not Included
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- Allows Backing Up
- 1100 lbs
- 1200 lbs
- 1300 lbs
- 1400 lbs
- Reese
more information >
Product Page this Question was Asked From
Strait-Line Weight Distribution w/ Sway Control - No Shank - Trunnion Bar - 12K GTW, 1,200 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Shank Not Included
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- 700 lbs
- 800 lbs
- 900 lbs
- Reese
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: How to Measure for Trailer Hitch Drop
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Determining Trailer Tongue Weight
- Q&A: Recommended Weight Distribution System for a 6,800 lbs 2019 Lance 2465 Travel Trailer
- Q&A: Bulldog Powered-Drive Kit Compatibility With 12K Ram Landing Gear
- Q&A: Can the Bulldog Powered-Drive Kit be Used on Any Jack
- Article: 5 Tips to Confidently Choose Your Weight Distribution Hitch
- Q&A: Installing a Brake Controller in 2014 Dodge Ram Pickup
- Q&A: Does The Curt True Course Allow The User To Adjust Its Sensitivity?
- Q&A: Can the Curt True Course Sway Controller Be Used With the New StabiliTrak Electronic Sway Control
- Q&A: Will Reese Weight Distribution System RP66131 Work for Trailer with 1,350 lbs Tongue Weight
- Article: Ball Mount Basics: Weight Capacity, Class, and Size