Replacement Landing Gear Motor for Venture Landing Gear with Motor M-9000 PK

Question

Question:

Is the Lippert LC142178 a direct replacement for a Venture M-9000 PK landing gear motor?

asked by: Butch

1

Helpful Expert Reply:

Yes, Lippert motor # LC142178 is the correct replacement motor for the Venture M-9000 PK motor for Venture landing gear. It is possible that the new motor will show a different serial or model number on its sticker but it is the correct replacement. I double checked with Lippert to confirm.

expert reply by: Michael H

1

click to enlarge

Answer 1

The Stromberg Carlson Replacement Motor #LG-196308 and the Lippert HD Motor #LC196308 referenced in your question are essentially the same motor. They can be used interchangeably on a landing gear system. With this in mind, I simply recommend…

view full answer...

Answer 2

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 3

It seems like you have the ADTH 1RV-200 Motor which has a capacity of 6,500 lbs. You can use this replacement motor #LC142178 which has a 4" on center mounting hole spacing. This one is a bit heavier duty than your other which could prevent it…

view full answer...

Answer 4

To replace the ADTH 1RV-200 motor on your landing gear the Stromberg Carlson #LG-196308 will work perfectly. This motor is rated for 6,500 pounds like your existing unit. For a gear box replacement you'd want the #LG-179015.

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 7

The only difference between these two 8,000 lb landing gear sets - other than price - is that one comes with the crank handle and the other does not come with the handle. - Comes With Crank Handle: Landing Gear Set w/ Handle #RVLG-8HDL - Comes…

view full answer...

Answer 8

To replace your existing Venture motor, the Lippert Components Venture 5th Wheel RV Landing Gear Motor #LC142178 is the correct replacement part for you. For an aluminum gear box, you are correct that you can use part #LG-179015. The #LC142178 motor…

view full answer...

Answer 9

We have the same part number basically twice through two different vendors here that are the exact replacement motor you are looking for. The Lippert part #LC142178 and the Stromberg part #LG-142178. They are the exact same motors and if I were you I…

view full answer...

Answer 10

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 11

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Replacement Landing Gear Motor for Venture Landing Gear with Motor M-9000 PK

Product Page this Question was Asked From

Continue Researching