Capacities of the Fastway Shank # FA92-02-4315

Question

Question:

What is the maximum GTW?

asked by: John C

0

Expert Reply:

The capacities for the Fastway Shank # FA92-02-4315 are 1,200 lbs tongue weight and 12,000 lbs total trailer weight.

expert reply by: Jameson C

0

Answer 1

The Curt Shank part #C17124 would give you right at 10 inches of drop when used with your Fastway e2 weight distribution system and would be what you'd want. The Curt and Fastway shanks are both made to the same dimensions which is what…

view full answer...

Answer 2

The Fastway e2 weight distribution system #FA94-00-1033 is rated for a maximum of 1,000 pounds tongue weight. To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the…

view full answer...

Answer 3

The shank included with all of the Fastway e2 Weight Distribution Systems offers up to 2-1/4" drop with round spring bars and a 2" drop with trunnion spring bars. If you need an additional 3-1/2" of drop for a total of…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Capacities of the Fastway Shank # FA92-02-4315

Product Page this Question was Asked From

Continue Researching