Trailer Breakaway System Recommendation for a 1993 Horse Trailer

Question

Question:

Looking for suggestions on a trailer breakaway with charger. It will be installed on a 1993 Shoop 2 horse gooseneck steel trailer - GVW is listed on the title as 3000 lbs. Dual axle. Any suggestions you have are greatly appreciated. Thank you!

asked by: Sarah H

0

Expert Reply:

The most popular trailer breakaway kit we offer is the Hopkins Engager part # 20099. This comes with a charger and a battery, plus a display on the box to let you know exactly what condition the battery is in.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

You will likely have several different grounds on any given trailer. The breakaway battery can ground by itself to the frame and to the trailer connector's ground if you want. But at the very least ground the battery to the frame. The brake…

view full answer...

Answer 2

If you are installing a trailer breakaway kit like #C52041, then you can use the 12-volt auxiliary power wire to help provide a maintenance charge on your breakaway kit's battery. A breakaway kit that does not have an onboard charger will have to…

view full answer...

Answer 3

The clamp of the Curt Breakaway kit part #C52026 that you referenced is 3 inches wide and 1-1/2 inches tall. It would work well on a 2 inch wide frame rail.

view full answer...

Answer 4

Trailer batteries (breakaway or auxiliary) do not have to be charged for the brakes to work with a brake controller when connected to a tow vehicle. You have two isolated problems possibility. A breakaway battery that won't hold it's charge…

view full answer...

Answer 5

In order to rewire your trailer, I strongly recommend you use the Trailer Wiring 7-Way Upgrade Kit part #HS381-9000 with the Bonded 4 Wire part #16-4B-1. This is going to ensure you have all the correct wire gauge and the junction box makes for a…

view full answer...

Answer 6

Yes, the breakaway battery must have a charge in order to send power to the trailer brakes and lock them up in the event of the trailer detaching from the tow vehicle. If the charge wire which is usually the 12 volt pin on the 7-way becomes…

view full answer...

Answer 7

You can reset the Hopkins Engager Push-To-Test Trailer Breakaway Kit #20099 simply by putting the pin all the way back into the switch. The only time the system would have to be replaced would be if something was wrong with it and even then the…

view full answer...

Answer 8

I am not entirely sure I understand your question. In regards to a breakaway system, the switch needs to have a separate battery for power according to most state regulations. You will need to check with your state's DOT but it is safe to assume…

view full answer...

Answer 9

Breakaway batteries shouldn't power other accessories even if the battery is larger. You really need the breakaway battery to be topped off at all times in case you need it. If you were to power other accessories you run risk of it being…

view full answer...

Answer 10

Yes. The only thing the switch does in a breakaway system such as #20099 is complete the circuit from the breakaway battery to the brake magnets when the pin is pulled from the switch. By inserting the pin back into the switch it separates the metal…

view full answer...

Answer 11

So you have a tow vehicle that has a 7-way connector on it and then a trailer that has a 5-way? What you would need to do is remove the 5-way wiring and install a 7-way with a lead like part #HM20048 which is a 7-way with 11 feet of harness. I…

view full answer...

Answer 12

The black wire on the Engager breakaway system #20099 will be connected to a 12v auxiliary power wire coming off of the trailer connector. This wire is typically the number 4 black terminal in the 7-way connector, but you will need to test to…

view full answer...

Trailer Breakaway System Recommendation for a 1993 Horse Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching