Recommended Trailer Hitch And Accessories for Light Duty Towing w/ 2010 Toyota Corolla
Question:
Need a light wt hitch for a 5x7 Trailer that will be hauling my Harley on the Corolla 2010.will this one you have work
asked by: Steve D
Expert Reply:
For light duty towing with your 2010 Corolla, I'd recommend the Draw-Tite Class I hitch, part # 24913. The hitch has the same capacity, but is less expensive. The hitch has a 2000lb towing/200lb tongue weight capacity, but according to the owner's manual, you'll be limited to a 1500lb towing capacity. I'd recommend you confirm the towing capacity for yourself by consulting the owner's manual or Toyota.
To complete your towing set up, you'll also need the following:
Ball mount, part # 3593
Trailer wiring harness, part # 118459
1-7/8 inch trailer ball, part # 19256 or # 19258 for a 2 inch ball
If you click the provided link, you can see an install video showing the hitch I recommended being installed on a 2011 Corolla.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 10K GTW, 1K TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Does Not Allow Backing Up
- 900 lbs
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: LED Trailer Taillight Recommendation for a 3110 Feather Lite Car Trailer
- Q&A: Replacement for Kwikee Revolution Step 9010000464 on 2011 Winnebago Journey 40U
- Q&A: What Are the Thread Sizes of the Orifice Connector for Trailer Brake Actuators
- Q&A: Replacing Trailer Actuator Buddy 32220 Reverse Solenoid on Triton Bass Boat Trailer
- Q&A: Troubleshooting No Power at the Tail Light Pin on a 2007 Toyota FJ Cruiser
- Article: Determining Trailer Tongue Weight
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Q&A: Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors
- Q&A: Converting From 7-Way Round to 7-Way Flat Connector
- Article: Will Flat Towing Blow Up Your Transmission?
- Article: Which Sway Control Hitch is Right For Your Trailer?