Trailer Hitch and Wiring for a 2016 Honda Civic EX Sedan
Question:
My question... any holes need to be drilled or the cutting of sheet metal/guards required for the installation of this hitch? Is it possible to install this hitch without putting the car on a lift? If possible please attach the installation manual - Thank You,
asked by: John
Expert Reply:
Drilling is required to install Curt trailer hitch # C11604 but there is no trimming mentioned. I have linked the instructions for you.
You can install the hitch without having the vehicle on a lift. If you have ramps or some jack stands then those will provide you will more space to work.
The recommended ball mount for this hitch is # C45521. For a 1-7/8 inch ball I recommend # 19256 and for a 2 inch ball I recommend # 19258. And for trailer wiring I recommend # 118686 to add a 4-Way flat to the back of the vehicle.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.
Curt also says you have to use stabilization strap # 18050 when using this hitch for any non-trailer load (such as a bike rack or cargo carrier) per their warranty requirements.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Concealed Trailer Hitches For a 2018 Honda Civic Sedan
- Q&A: Recommended 4-Way Wiring Harnesses for a 2019 Honda Civic Hatchback
- Q&A: Recommended Class I Trailer Hitch for a 2021 Mercedes-Benz E-450
- Q&A: Dimensions of the Curt C11604 Hitch for a 2016 Honda Civic
- Q&A: Installation of Curt Class I Trailer Hitch on 2016 Honda Civic Sedan
- Q&A: Does the Yakima Hold-Up 2 and Yakima Two-Timer use the same tongue assembly?
- Q&A: Which Ball Mount Fits Curt Class I Hitch for 2018 Honda Civic # C11604
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Trailer Hitch Installation Tips
- Article: Best Bike Racks for Electric Bikes
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: What is Boondocking