Trailer Hitch Comparison and Recommendation for a 2013 Ford Explorer
Question:
Whats the difference between the Curt Class III, part # C13100 and the Draw-Tite # 75710?
asked by: Ahmed
Helpful Expert Reply:
The Draw-Tite # 75710 has been discontinued and replaced with part # 76034.
Due to their very similar design and capacities they are not really that different at all. Curt has only a powder coat finish whereas the Draw-Tite has an e-coat base covered by powder coat.
I would recommend the Curt # C13386 as that is what I would buy for your 2013 Ford Explorer.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with the right rise or drop to tow the trailer level, check out the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
For trailer wiring you would want the part # C56172. I attached an install video for you to check out as well.
Products Referenced in This Question
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Replacement RV AC Unit for Dometic B57915.711J0
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Winch Repair Kit for Dutton-Lainson Trailer Winch Model DL1602A
- Q&A: Replacement Parts for ELX-45 Power Converter
- Q&A: Replacement For Fulton Drop-Leg Stabilizer Jack
- Q&A: Amount of Play on Dexter 12K Torflex Axle Under Max Load
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Q&A: Charging Auxiliary Battery from Car Cigarette Lighter or 12 Volt Auxiliary Plug Connector
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Best Vehicles to Flat Tow Behind an RV
- Article: Surviving the Night in a Teardrop Camper...During a Winter Storm
- Article: How to Choose the Right Trailer Hitch Class
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)