Grease Seal Availability with Inner Diameter 1.5 and Outer 1.987

Question

Question:

I am having trouble getting the part numbers for the axle seal. ID 1.5 OD 2 Would you know the part numbers for a 13 ft Boler Trailer with a dexter axle number 9? ID 1.8 OD 2.55 Thanks

asked by: Mike B

0

Expert Reply:

Try measuring your old grease seal again as most likely the part # 10-9 would be the correct seal you would need. This seal has an inner diameter of 1.50 inches and an outer diameter of 1.987 which is pretty close to what you have but not quite the same. This would be the best option we could provide.

The closest grease seal to match the second set of dimensions is the part # BB60002 that has inner diameter of 1.875 and outer diameter 2.560.

expert reply by: Jameson C

0

Answer 1

Thank you for providing the part number from your existing grease seal, part 16074-224. Based on my research I found that part #10-9 is an equivalent replacement part. I have also linked a helpful article and video concerning bearings and seals.

view full answer...

Answer 2

The difference between the single lip and double lip seals is that the double lip grease seal will have two rubber lips that are in contact with the spindle. The double lip grease seals are usually used in marine applications to give a better seal…

view full answer...

Answer 3

The Dexter Trailer Idler Hub Assembly #8-258-5UC1 that you referenced actually uses the same #L44649 inner and outer bearing, which has a 1.063 inch inner diameter. Many trailer hubs though do use different size inner and outer bearings and this…

view full answer...

Answer 4

I did a little digging on your grease seal number and it looks like the 16074-224 has an inner diameter of 1.5 inches and an outer diameter of 1.987 so the correct part number you would need is the #10-9.

view full answer...

Answer 5

Two grease seals match closely to your required inner and outer diameters. The linked page displays parts #RG06-020 (a pair of seals) and #10-9 (a single seal). Both have an inner diameter of 1.500-inches and an outer diameter of 1.987-inches.

view full answer...

Answer 6

The correct replacement braking assemblies for the Kelsey Hayes 602027 and 602028 is the Electric Trailer Brake Kit part #AKEBRK-35. These will be direct bolt-on replacement. I would add the Mounting Hardware for 10" Brake Assemblies part…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...