Recommended Roller Bunks For Boat Trailer With Cobalt 206 Boat

Question

Question:

I removing my bunks on my trail and would like to replace them with roller bunks. I have a cobalt 206 made in 2000. the trail has 4 bunks on it 2 6 inch wide bunk by 5 feet long 2 4 inch wide bunk by 10 feet long.. what is the best way for me to do this. I will like to have to install the wooden bunk after I paint the trailer.

asked by: Mazen Z

0

Expert Reply:

The roller bunks I recommend for your Cobalt are the Dutton-Lainson Boat Trailer Deluxe Roller Bunk, part # DL21741.

These bunk rollers are 5 ft long and each section has 6 sets of 3 rollers, that helps make loading and unloading the boat much easier. Since these come in 5 ft sections you can place them end to end for the 10 ft section you need to take care of on your trailer.

These can be mounted directly to the wooden bunks you currently have, and would raise the boat by the height of the roller bunks, or you can purchase Boat Trailer Roller Bunk Bracket, part # DL21742 separately. You would need 4 of these for each pair of bunk rollers.

expert reply by: Jeffrey L

0

Answer 1

Yes you can use a different size roller bunks as a replacement. You can mount the Boat Trailer Deluxe Roller Bunks, #DL21741, directly to the top of your existing wooden bunks. If mounted in this fashion you will not need any brackets. You will want…

view full answer...

Answer 2

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 3

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

The best option for a Class C motorhome windsheild cover is going to be the Adco Deluxe Cover part #290-2507 which is designed for Class C motorhomes just like yours. I attached a review video for this cover for you to check out as well.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The adjustment holes on the Super Titan Forged Pintle Hook Plate part #RP38186 are 17/32" diameter so they will accept and are designed to be used with 1/2" bolts. It should not matter what brand pintle hook is used as the hole size and…

view full answer...

Answer 10

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

I looked up the dimensions of your High Pointe EC942K9E and it's 15 inches deep, 15.7 inches tall, and 29.9 inches wide so the Furrion Over the Range RV Convection Microwave #FMCM15SS would easily fit in place of it and would also work really…

view full answer...

Recommended Roller Bunks For Boat Trailer With Cobalt 206 Boat

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching