Trailer Hitch Recommendation for a 1998 Ford Ranger
Question:
I have a 1998 Ford Ranger XLT 2 wheel drive my question is will it fit and would I have to drill any holes? Thank You for any info.!!!
asked by: Roy D
Expert Reply:
The Curt Hitch part # 13138 that you referenced has been confirmed as a fit for your 1998 Ford Ranger so it would be the hitch for you to go with. There will be some drilling required for installation of this hitch. I attached an install video for you to check out that shows the hitch being installed on a similar 1999 Ranger.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with the right rise or drop to tow the trailer level, check out the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
For trailer wiring you would want the # 118325.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: 2003 Ford Ranger Hitch Receiver Recommendation
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Will the 6 on 5-1/2 Kodiak 12" Rotor item # KR12S Replace a 12” UFP Brake Rotor?
- Q&A: Recommended Trailer hitch Receiver For a 2008 Ford Ranger 4x4
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Trailer Hitch Receiver for 2004 Ford Ranger Edge
- Q&A: Fit And Compatibility Of The Kodiak 10" Rotor With The UFP DB35 Brakes
- Q&A: Replacement Disc Brakes, Bearings, and Actuator for 2010 EZ Loader Boat Trailer
- Q&A: Can a Double-Lip Trailer Hub Seal be Used in Place of a Single Lip Seal
- Article: Frequently Asked Questions About Transmission Coolers
- Article: Which Hitches are Made in the USA
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Flat Towing Package for 2008-2011 Honda CR-V