Weight Distribution System Recommendation for 2013 Ford F-150 Pulling 2015 Cougar w/ 1200 LB TW
Question:
i have a 2015 cougar xlite 33res 36 loaded at 8700 lbs and tongue wt. is 1200 lbs on a 2013 f150 with 6.2L ext cab what type setup do i need.
asked by: Larry K
Expert Reply:
A key component to choosing the correct weight distribution system is knowing the trailer's exact tongue weight. Tongue weight is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind the rear axle of the tow vehicle. The ideal situation is to have the loaded tongue weight of your setup to fall right in the middle of the tongue weight range of the system you use.
Since you already know that the tongue weight of your trailer is 1200 lbs, I recommend the Strait-Line Weight Distribution with Sway Control, # RP66130. This system is going to accommodate tongue weights of 800 to 1,500 lbs and featuring dual-cam sway control to stop trailer sway before it begins. I have included a short video review for you.
To complete the set-up you will also need Weight Distribution Shank, # RP54970, and Hitch Ball, # C40086 for 2-5/16 inch or # A-90 for 2 inch.
Just a reminder, you will want to ensure that you aren't exceeding the weight limitations of any component in your towing setup. This would include your F-150, the hitch, and the weight distribution system.
Products Referenced in This Question
2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-5/8 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 10000 lbs GTW
- Class IV
- Class V
- CURT
more information >
2-5/16" Hitch Ball w/ 1" Rise - 1-1/4" Diameter x 2-5/8" Long Shank - Raw - 25K
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Raw Steel
- 2-5/16 Inch Diameter Ball
- 2-5/8 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 25000 lbs GTW
- Class IV
- Class V
- CURT
more information >
Reese Weight Dist Shank - 12-1/4" Long - 2" Drop to 6-1/2" Rise - 1,500 lbs TW
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- Fits 2 Inch Hitch
- Round - 2 Inch Drop
- Trunnion - 1 Inch Drop
- Round - 5 Inch Rise
- Trunnion - 6 Inch Rise
- Reese
more information >
Product Page this Question was Asked From
Strait-Line Weight Distribution w/ Sway Control - No Shank - Trunnion Bar - 15K GTW, 1,500 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Shank Not Included
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- Allows Backing Up
- 1100 lbs
- 1200 lbs
- 1300 lbs
- 1400 lbs
- Reese
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Can Blue Ox SwayPro Weight Distribution be Used With Equal-i-zer Weight Distribution Shank
- Q&A: Is There a Trailer End 4-Round With Wires
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Recommended Tongue Weight Capacity for a 2020 Chevrolet Silverado 2500
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: How to Measure for Trailer Hitch Drop
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Q&A: Will 18" Long Equal-i-zer Weight Dist Shank Reduce Tongue Weight Capacity
- Q&A: Replacement Trailer Grease Seal for an NOK AD2527E Seal on a Boat Mate Trailer
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Q&A: Will Reese Weight Distribution System RP66131 Work for Trailer with 1,350 lbs Tongue Weight
- Q&A: Will Lift Bracket RP6637 and Chains 3216 Fit on Pro Series RB3 Weight Distribution System