How to Install a Brake Controller on a 2006 Nissan Murano
Question:
Hello Do you have any advice for installing this in the 2006 Murano? Nissan seems nervous about installing any controller as the Murano does not have pre-wired brake controller plug - they say they have to take out the dash to hardwire it in. A very expensive way to go - any advice?
asked by: Lynn S
Expert Reply:
There is no need to remove the dash to install a brake controller. You will have to run 3 wires through the firewall and into the engine bay, but you can probably find a grommet that already has wires running into the engine bay to do this.
Since the Murano was not built with a factory trailer connector with the provision of a brake circuit, you will need to add one, usually a 7-Way.
We have a complete 7-Way and Brake Controller install kit, part # ETBC7. It requires that the vehicle have a properly function 4-Way connector to build on. If you do not already have one, the proper 4-Way for your 2006 Murano is part # V30204.
The ETBC7 will plug into your 4-Way, then you will connect the 4 loose wire leads. The purple wire will need to be spliced to the reverse light circuit on your Murano, only if the trailer has reverse lights. The white wire needs to be connected to a good ground point on the vehicle frame. The blue and black wire need to be connected to the included length of jacketed 2-wire. The black lead needs to be connected to the positive battery terminal with the 40 amp breaker in-line. The blue needs to be run to the blue wire off the brake controller.
Now that the 7-Way is installed, you can wire in the brake controller. Again the blue on the brake controller needs to be wired to the blue wire on the 7-Way. The white wire needs to go to the negative terminal of the battery. The black wire needs to be run to the positive terminal on the battery with a 20 or 30 amp breaker depending on controller model. Finally the red wire needs to be connected to the wire coming off the brake pedal switch that only goes hot when the pedal is pressed.
I have included a link to a couple of videos that show an installation of a brake controller and an ETBC7 on a Toyota FJ Cruiser. I have also included a write-up on installing a brake controller from scratch.
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: Most Popular Wheel Bearings
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Lift Kit Options For A 2015 Winnebago Micro Minnie 1706FB
- Q&A: Lug Nut Torque Chart for Trailer Wheels