Installation Instructions for Draw-Tite Trailer Hitch # 24711 on 2006 Chrysler Sebring Convertible
Question:
Ihave the 24711 hitch for my car but do not have the instructions for installing the hitch. I see the holeson the passenger side, and the exaust holes on the drivers side are threaded, but is that enough to hold the hitch? Is there more that I do not have?
asked by: Ralph C
Expert Reply:
Installation of the Draw-Tite Class I Trailer Hitch for the 2006 Chrysler Sebring Convertible, item # 24711, is fairly simple, you will need to install the hitch loosely in two existing holes and then drill two 1/2 inch holes in the frame rail. The exhaust bolt holes are not used on this vehicle.
I have posted a link to the instructions for this hitch and the pictures on the product page should provide some help.
Some items you may need to complete your towing setup with Class I hitch are listed below.
Drawbar # 3592
Wiring # C59496
Hitch Ball # 19256 or # 19258
Hitch Lock # e98879
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 1-1/4" Hitches - Flush - 2-1/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 1-1/4 Inch Hitch
- Flush Pin
- 2-1/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: How Much Slack Is Needed In Trailer Wire Connection To The Tow Vehicle?
- Q&A: Lug Nut Torque for a Trailer Wheel
- Article: Harvest Hosts
- Q&A: Does Furrion Single Zone Controller part # FACC12SA-BL Have Dip Switches
- Q&A: Installing a Brake Controller and a 7-Way Trailer Connector on a 2005 Ford F-150 With Factory 4-Way
- Article: Replacement Automotive Lighting
- Q&A: Replacing Integrated Brake Controller of 2008 Ford F-350
- Q&A: Bearings and Seal Used for AL-KO 7290 Trailer Hubs for #99 Spindles
- Q&A: AxleTek Brake Assembly Recommendation for 8k Axles with 4 Bolt Mounting Pattern
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Measure a Trailer Axle