Trailer Hitch, Wiring, Brake Controller and Accessories for a 2011 Nissan Xterra
Question:
I have a 2011 Nissan Xterra tow capacity 5000 lbs. It does not have a factory tow package, but it does have the plug at the drivers side rear leaf spring area. I will be pulling a 2013 Rockwood Popup Camper HW276. GVWR is 3800 / dry weight is 3127 / payload capacity 670 / hitch weight 270. I was researching your website and want to confirm these parts for the above: 1 Curtis Hitch part # 13514 2 Wiring harness for 7 way plug for no current tow package Part # 118266 3 Curt Brake Controller with the ADAPTER part # C24VV and C51515 4 Brake Controller Wiring from brake controller to 7-way plug part # ETBC7 Other questions: A Ball and receiver? I was told the camper measurement is 22inch from the ground to under the ball receiver area. I was told it uses a typical 2inch ball? B Theres a note about a circuit breaker 9506P for # 3 above. Do I need that if it comes with an adapter already? PS: any instructional videos are a super plus :
asked by: Karen C
Expert Reply:
For your 2011 Nissan Xterra Curt hitch # 13514 and wiring harness # 118266 will work just fine. Brake controller and harness # C24VV and # C51515 are also going to work just fine. But instead of using # ETBC7 you would use # 5506. this is because you do not need all of the stuff included with the ETBC7.
You will still need to route the brake controller blue output wire to the back of the 7-Way, attach it to the back of the 7-Way in the 7 o'clock position. Remove the wire that is already there first though.
A receiver is the opening on the hitch so I think you mean a ball mount and ball. On the hitch it will measure approximately 18 inches from level ground to the top of the receiver opening. If the trailer coupler is 22 inches from level ground to the bottom of the coupler with the trailer level then you will need a ball mount with a rise of 4 inches, # C45070, to tow the trailer level.
For a 2 inch ball that fits this ball mount use # 63845.
The circuit breaker needed to install the brake controller is included with 5506.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 7-Way Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt TriFlex NEXT Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- CURT
more information >
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 4 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Universal Wiring Adapter for Curt Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Universal
- CURT
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Replacement Wiring Harness for Tow Ready Nissan Vehicle Wiring Harness
- Accessories and Parts
- Custom Fit Vehicle Wiring
- Wiring Harness
- Tow Ready
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Troubleshooting Flashing Red LEDs On The Redarc Tow-Pro Liberty RED24FR
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Troubleshooting 4-Way to 7-Way Wiring Upgrade on 2006 Nissan Pathfinder
- Q&A: How to Connect Two 6V Batteries for 12V Power
- Q&A: Do the AirLift 1000 Air Helper Springs for Coil Springs Fit 2020 Jeep Gladiator with 2 Inch Lift
- Q&A: Does Trailer Lighting Ground Through the Hitch Ball
- Q&A: Troubleshooting Redarc Tow-Pro Liberty Brake Controller on 2022 Honda Ridgeline
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Must-Have Flat Towing Components
- Q&A: Installing Trailer Wiring Harness on 2013 Nissan Xterra w/out Tow Package
- Article: The Best Towing Mirrors
- Article: What is the Best Trailer or RV Storage Cover