Hitch Recommendation for a 2014 Ford Focus to Tow Small Trailer
Question:
Am going to tow a small trailer behind my 2014 Focus that will haul a golf cart and want to know which hitch to buy. Thanks
asked by: Fred
Helpful Expert Reply:
We have everything you need so that your 2014 Ford Focus can tow a trailer.
For a hitch I would recommend the Curt part # C11158 as it has been confirmed to fit your vehicle. You will need ball mount number 3593. I attached an install video for you to check as well.
You will also need a hitch ball to complete the connection. For that you would want the part # 19256 for a 1-7/8 inch hitch ball or part # 19258 for a 2 inch hitch ball. For trailer wiring you would want part # 118548. I attached an FAQ article on towing that should be helpful as well.
You will want to check the owner's manual of your vehicle to determine the towing capacities and be sure not to exceed these figures with the weight of your trailer and golf cart. If this hitch has different capacities than your vehicle you will want to go with the lower capacities as the overall capacity.
![Jameson C](https://images.etrailer.com/static/images/catg/people/371_tn.jpg)
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Printable Trailer Bolt Hole Pattern Template
- Article: Trailer Hitch Receiver Sizes
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Flat Towing Package for 2008-2011 Honda CR-V
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Will Curt T-Connector Fit 2015 Ford Focus ST Hatchback
- Article: What Do I Need To Tow A Trailer?
- Q&A: Trailer Wiring Harness Recommendation for a 2014 Ford Focus ST Hatchback
- Q&A: How Can I Get Additional Trailer Wiring Signals at the Rear of my Durango
- Q&A: How Does Hitch Tongue Weight Rating Affect Use of a Motorcycle Carrier on a Toyota Sienna
- Q&A: Curt Echo Brake Controller for 2023 Jeep Grand Cherokee 4xe
- Q&A: How To Wire Up Hopkins Engager Push-To-Test Trailer Breakaway Kit