Purpose of the Spacers in the Pro Series Weight Distribution System # PS49582

Question

Question:

where does the sway control spacer go? Why would I need it?

asked by: JR

0

Expert Reply:

The spacers that come with the Pro Series Weight Distribution System # PS49582 and # 83660 that you referenced are designed adjust the angle of the hitch ball so that you get the correct amount of spring tension to properly distribute the weight of the trailer tongue weight.

Check out the install video I attached for this WD system as well. At the 1:00 mark the spacers are shown.

expert reply by: Jameson C

0

Answer 1

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 2

For a weight distribution system, there are always exceptions,but in general the systems with only bars and chains do not have sway control. They are adjustable in tension for different weight, but are a little more work. The bar systems whether…

view full answer...

Answer 3

I went out into our warehouse and grabbed a 2-5/16" Hitch Ball #C40085 to measure and found it is from top to bottom 5-3/4 inches tall.

view full answer...

Answer 4

The ball measures 2-3/4 inches from the ball mount surface to the top of the ball. I am glad to see that you are making sure you get the proper ball mount for your tow set up. The rule of thumb is to be no more than 2 inches over or under. The…

view full answer...

Answer 5

The B&W Continuum #BW78FR and the Reese Strait-Line #RP66083 are both great systems. The B&W Continuum is going to be easier to set up, but as far as sway control goes, I definitely have to give the edge to the Reese Strait-Line. The…

view full answer...

Answer 6

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 7

You're welcome Chris! Sounds like you've more then got the hitch covered. I can not think of a better option then the TorkLift SuperHitch Magnum Trailer Hitch item #TL74FR. You will be able to pull anything and everything with this hitch and…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Tom, you are on the right track. I checked out your 2023 Jayco Jay Flight 284 BHS and it does have an underslung coupler so the correct B and W Continuum weight distribution would be the part #BW88FR. An underslung coupler is basically one that…

view full answer...

Answer 12

Accuracy is the most important thing when it comes to tongue weight scales in my opinion and convenience is a plus. The etrailer Tongue Weight Scale #e99044 is both. I have gotten my hands on this product and used it. One of my favorite things about…

view full answer...

Purpose of the Spacers in the Pro Series Weight Distribution System # PS49582

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching