Dimensions for Ultra-Fab Steel Jumbo Roller # UF48-979023

Question

Question:

What are the overall dimensions of this roller, i.e. from bottom of roller to top of mounting plate and width of mounting plate? Also, do you know what the maximum weight rating is for this roller? I want to use it on a 38foot rear engine Newmar motorhome. Thanks,

asked by: Ron R

1

Helpful Expert Reply:

The overall height from the bottom of the roller to the top of the mounting plate of the Ultra-Fab Steel Jumbo Roller # UF48-979023 is 3 inches, the width of the mounting plate is 2-1/2 inches.

These don't have a weight rating because the way they are used would make it hard to give them a rating. My contact at Ultra-Fab said that because these rollers are not meant to sustain weight for extended periods of time, they do not have a weight capacity.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Ultra-Fab Skid Wheel part #UF48-979023 measures 3-1/2-inches tall overall, including the weld-on mounting bracket. Just the round wheel part only is 2-1/2-inches tall. Please refer to the linked photo for dimensions.

view full answer...

Answer 2

Thank you for providing a photo diagram of your 5th wheel rear frame area where you are intending to install Ultra-Fab Steel Micro-Roller Skid Wheels #UF48-979021. The best location to weld on these rollers is at or just behind the point where the…

view full answer...

Answer 3

I do have an option for you. Due to the length of your 5th wheel and size of your bumper, we do not have a bolt-on option available. That being said, you can use the Ultra-Fab Steel Jumbo Roller for Trailers and RVs #UF48-979023 which is a weld-on…

view full answer...

Answer 4

The skid wheel part #UF48-979023 would work well for you as it's the largest size we have to fit your trailer. This shouldn't hurt your frame strength either. The more you have the better it will distribute the weight. So going with one on…

view full answer...

Answer 5

We do not have the CAD drawings or blueprints for the Ultra-Fab Steel Roller, part #UF48-979020, but I have attached a photo of the roller with dimensions shown. The mounting bracket measures 1-1/4 inches from the center of the hitch pin hole to the…

view full answer...

Answer 6

Sway controls are designed to be used in situations where sway is a direct result of some type of road condition, like high winds or large vehicles passing. If you have sway with a trailer under normal towing conditions, sway control will most likely…

view full answer...

Answer 7

The Center Hanger for TruRyde Equalizer #TRHG291-C is specifically designed to be used with the Equalizer for 2" Wide Slipper Springs #TREQ4541. This is designed to work with trailer axles from 6,000-8,000lbs. The Redline Center Hanger for…

view full answer...

Answer 8

Installing an anti-sway bar at the rear of your truck may help control some of the trailer sway, but will not prevent trailer sway from happening. Installing a sway bar helps reduce the body roll and sway you will see on the tow vehicle, but does…

view full answer...

Answer 9

You may have the tow package on your 2014 Ram 2500, but if you do not have the pucks visible in the bed of your truck you do not have the hitch prep package needed to install the #BWRVK3600 but I do have a solution for you. You would want to install…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Dimensions for Ultra-Fab Steel Jumbo Roller # UF48-979023

Product Page this Question was Asked From

Continue Researching