Wiring 2007 Dodge Ram 3500 For Installation of Flat Bed
Question:
I am in the process of removing the bed and installing a flatbed. I was curious if there is a pigtail I can wire to the lights on the flatbed so that I can plug in to the factory brake/tail lights. I would rather not cut the factory wiring so that I have the option of re-installing the factory bed when I sell it. The truck does have the factory trailer wiring with the additional RV plug in the bed but if at all possible I would like to keep the trailer wiring on a separate circuit.
asked by: Roger M
Expert Reply:
We don't offer a direct part, but I know how you could fabricate a pigtail. You'd need part # 118381 that would plug inline with the harness that plugs into the rear of the 7-way. You could simply cut the 4-pole off and wire the yellow wire to the left turn, the green wire to the right turn, ground the white wire and run the brown wire to the running light and jumper it over to the running light on the other side.
This set up would provide you with a quick disconnect. You'd need to wire into the lamps on the flat bed, but the factory vehicle wiring would remain intact.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Product Page this Question was Asked From
Multi-Plug T-One Connector Assembly for 7-Way & 4 Pole Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- 7 Round - Blade
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: CURT Dodge OEM Harness Adapter
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Female PL-3 Plug - Qty 1
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Pigtail - Qty 1
- Shop: BOLT brand vehicle and hitch locks
- Shop: Curt Hitch Lock - 2", 2-1/2", and 3" Hitches - Chrome
- Shop: Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers for 3" Hitch - 6" Drop/Rise - 32K
- Search Results: 3" ball mount
- Search Results: locking hitch pin
- Search Results: c61502
- Shop: Trailer Hitch
- Search Results: idler hub
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Search Results: rvk3050
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Search Results: load equalizer
- Search Results: 3500 lb boat trailer axles
- Shop: Gooseneck Hitch
- Shop: Vehicle Tow Bar Wiring
- Article: Trailer Wiring Diagrams
- Q&A: How to Combine Taillight Circuits Stop and Turn Onto One Circuit
- Video: Review of Peterson Trailer Lights - Drivers Side LED Tail Lights - PE46CR
- Video: Trailer Wiring Harness Installation - 2006 Dodge Ram Pickup
- Shop: Tool Box
- Shop: Suspension Enhancement
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Q&A: Junction Box To Wire Lighting on Flatbed Trailer
- Q&A: Are Diodes Required to Separate Brake Lights from Turn Signals Using Converter 118158 on Trailer
- Q&A: Can Diodes be Used to Combine Brake Lights and Turn Signals
- Video: Review of Diamond Lights - Load Resistors - DI34ZR