Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this CURT Custom Fit Vehicle Wiring

• Trailer Hitch Recommendation for a 2006 Ford F250 Crew Cab
  I would personally recommend going with the Curt Custom Fit Trailer Hitch Receiver, # C14355, for your 2006 Ford F250 Crew Cab. This hitch is specifically designed for your Ford F-250 and will bolt directly to your frame with no welding required. In order to be fully prepared to tow, you may also need Trailer Wiring, # C56032, and Ball Mount Kit, # EBMK2416.
  view full answer...
• Installing A 7-Way On A 2003 Ford F-350 Super Duty
  Hey Edward, The factory connector for a 2003 Ford F-350 7-way socket should be round so it's likely that you're looking at a different wire harness. Could you send me some pictures and I can take a look? It's also possible that your F-350 wasn't setup with a factory wire harness and you'll instead need to first install a 4-pole connector # C56032 and then install a hardwired 7-way socket # ETBC7 instead of the factory harness plug-in version # C55774 that you ordered.
  view full answer...
• Parts Needed to Add 7-Way and Brake Controller to 2000 Ford F-350
  First thing your 2000 Ford F-350 needs is the correct 7-way adapter confirmed as a fit for your truck. For that you'd want the part # 118243 which plugs into the factory wiring of the truck and comes with all of the needed relays and fuses. Next you'll need the install wiring adapter as well as a brake controller. For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it...
  view full answer...
• Parts Needed to Wire in a Brake Controller to a 2006 Ford E-350 without any Trailer Wiring
  Since you have no trailer wiring at all on your 2006 Ford E-350 you will need to start with a 4-way. For that you would want the # C56032 which is a confirmed fit for your van. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
  view full answer...
• Recommended Vehicle Wiring for Trailer Connection On 2005 Ford F-250
  For your 2005 Ford F-250, I recommend the 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End # HM40975 if you have a factory 7-way or factory 4-way. If you prefer the look of the # 118243 which is not a confirmed fit, I recommend the Replacement Multi-Tow 7-Way & 4 Pole Trailer Connector # 74682. If you truck does not have the factory 7-way wiring, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56032. Then to get 7-way...
  view full answer...
• What Class 3 Hitch Should I Put on My 2007 Ford F-350 Super Duty
  When installing a class 3 hitch on your 2007 Ford F-350 Super Duty I recommend The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # 13355. This hitch has a gross towing weight up to 6,000 pounds and has a tongue weight up to 600 pounds. Always check your vehicle's manual to determine the correct towing capacity for your vehicle. The hitch has a concealed cross tube which gives it a clean look after it is installed. It has a bolt-on installation with no drilling required....
  view full answer...
• Will the Curt T-Connector Wiring Harness C56032 Fit a 2007 Ford F-250/F-350 with Diesel Engine
  The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # C56032 is a confirmed fit for a 2007 Ford F-250/F-350 with Diesel engine.
  view full answer...
• Installing Trailer Wiring Harness on 2005 Ford F-250 with Bad Factory Connectors
  If the connectors on your 2005 Ford F-250 where harness # C56032 plugs into are bad, then you would have to replace that part using either an aftermarket part from an auto parts store or the OEM part from the dealer. The other option is to hardwire the harness into the wiring on the truck and bypass those connectors. To do that you would need a circuit tester such as # PTW2992 to test the wiring on the vehicle to determine the functions. The 4-Way would then splice in as follows: white...
  view full answer...
• Recommended 4-Pole Trailer Connector for 1999 Ford F350
  The Curt # C56032 isn't a fit for the 1999 Ford F350, but we do offer an option that will work. If you have the rectangular tow package connector on the driver's side frame rail behind the rear tire, you'll want to use the Hopkins # HM40155. If you have the round connector, use part # HM40975 which provides both a 7-way and a 4 pole.
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?