Part Numbers: SS98GV,31302
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
82 x 14 Residential plow with thick rubber cutting edge self-adjusts up and down to smoothly clear a path on any terrain. Aluminum blade stays in straight-ahead position, and makes plowing your driveway as easy as pulling forward or backing out.
Features:
Specs:
Snowplow Installation
Front or rear mount? Versatility is the SnowSport LT's middle name.
Installation is quick and simple - just slide the included shank assembly into your 2" hitch receiver and secure with pin.
Once the plow frame is connected, attach the blade by lifting one end at a time onto the frame's holders. The lightweight aluminum blade construction makes lifting or adjusting an easy, one-person job. Secure the blade in either the transport or plowing position with the plow's snap pins. The low-profile design won't block your headlights, and the transport position is secure enough for highway travel.
If using with a rear-mount receiver, simply lower the blade to plow position and back up as usual. For a front-mounted plow blade, just drive forward with the blade in the plow position. The unique design takes the hassle out of plowing: This device has no hydraulics or complicated wiring. The push frame on the shank assembly allows the blade to move along the grade of the terrain for easier, more efficient plowing. The heavy-duty rubber cutting edge is effective yet turf friendly, collecting snow and squeegeeing slush without digging into the ground.
When you are ready to reverse your driving direction, the blade lies back, skimming over the surface of the ground until you change direction again to plow.
Handy blade markers extend vertically from the ends of the plow to help you see where you are plowing.
With the SnowSport LT, plowing snow is as easy as backing out of your driveway. Once you are finished plowing, simply lift the blade, refasten it in the transport position and head off for work or errands.
California residents: click here
Easily attach a variety of accessories to the front of your vehicle with this corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2003 Chevrolet Tahoe we'll be installing the CURT 2" front-mounted hitch, part number 31302. Now with our hitch already installed you can see it's nicely concealed behind the front fascia. The only thing sticking out is the receiver tube. It's got a 5/8 pinhole and a 2" by 2" receiver tube. This is a class three hitch. It has 500 pounds of tongue weight capacity and 5,000 pounds of tow capacity with a 9,000 line capacity.
The sleek design keeps most of it behind the fascia with just a little bit that's visible through the tow hook cutout in the fascia. It is also designed to work in conjunction with vehicles previously equipped tow hooks. Next I'll go ahead and give a couple measurements that will assist you with selecting for your new hitch. from the center of the hitch pinhole to the outermost edge of the front bumper is 6-1/4". From the top of the receiver tube opening to the ground is 10-3/4". This will assist you with selecting accessories such as a snowplow, winch, or cargo basket.
Now we'll go ahead and show you how to install the new hitch. Now to begin our install we'll go ahead and note that the vehicle is already previously equipped with factory front-mounted tow hooks. With that, we'll need to remove the manufacturer's bolt at the bottom of the frame. Now with the bolt out it's easy to see the forward and rear attachment points. We'll be using the hole cut out here in the frame as our rear attachment point on each side and for that attachment point we're going to install a 1/2" carriage bolt and block. The carriage bolt and block will go in the frame, then down through the hitch, where it will get secured with a 1/2" flange nut.
To get our hardware into the frame we're going to use the 1/2" bolt leader supplied with the install kit. To get our hardware into the frame we're going to use a reverse pull method. Start by sliding on our block, then threading on the carriage bolt. Feed the bolt into the frame first, followed by the block. We'll pull them both back down over the manufacturer's hole to create our attachment point. Next we can put our side bracket in place.
To do that we're going to reuse the manufacturer's bolt for our forward attachment point. Slide it over the bolt we just installed, then reinstall the manufacturer's bolt into the weld nut built into the frame with the tow hook, noting on applications that do not have a tow hook you will install another carriage bolt and block to create the forward attachment point hardware. Now with my bolt in place we'll go ahead and take the flange nut and thread it onto our carriage bolt. Now we're going to install our hardware loosely until we have it all in place. Now with our passenger side done I'm going to move over to the driver side and repeat the same process. Now with both side brackets in position but loosely installed, we're ready to put the hitch cross tube into place. We're going to secure it with the new 1/2" bolt that will go through the hitch, then through the side bracket, and get secured with a 1/2" flange nut. Now it's a good idea to get an extra set of hands to help you hold the hitch while you install these fasteners. Now with all our fasteners installed we'll go ahead and tighten them down. Once I have the brackets tightened down to the frame we'll then go ahead and tighten down the hardware that secures the cross tube to the brackets. Now once we have them all tightened down we can go ahead and torque to specifications as indicated in the instructions. That will complete our install of the CURT front-mounted hitch, part number 31302, on our 2003 Chevrolet Tahoe. .
Average Customer Rating: 4.8 out of 5 stars (176 Customer Reviews)
82 x 14 Residential plow with thick rubber cutting edge self-adjusts up and down to smoothly clear a path on any terrain. Aluminum blade stays in straight-ahead position, and makes plowing your driveway as easy as pulling forward or backing out. Easily attach a variety of accessories to the front of your vehicle with this corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement.
I thought these product would be packaged better from the factory for shipping resilience.
I gave this hits only 4 stars since all of the available information indicated it would bolt right on to my 2003 Avalanche 1500 (All Models) with no modification, but it wasn't quite that simple. First off, my Avalanche has the plastic cladding. The end brackets of the hitch push the bottom of the air dam under the bumper down a bit and make it bow out. I had to remove the bracket that secured the air dam to the center of the frame. I mounted the hitch in the upper position since I didn't want it to be so low, and the receiver ends up being 8" back from the bumper facia. I had to order an 8" extension to bring it out past the bumper. Other than that, I'm happy with the hitch. I just wish the fitment guide was a little more specific.
Bryan C.
8/13/2013
Did the hitch still come out under the cladding? Or do u need to make a hole for extension? Thanks Bryan 2004 avalanche with clading
William
8/20/2013
Since I installed the hitch in the upper position, I had to cut a hole through the claddingbumper. This came out near the bottom of the license plate recess. I then use the 8 extension if needed. This brings the receiver out in front of the bumper.
This hitch was very easy to install....I had to trim the lower air dam to fit around the receiver and that gives it a clean neat look.
I didn't like that I had to remove and leave the shields around the tow hooks off. But overall I'm very pleased.
I plan to use this hitch for maneuvering a camper in a narrow spot beside my home, and for a bike rack when towing a camper.
Paul T.
11/2/2017
The Curt front hitch is GREAT!I use it to help move my camper beside my house which is lacking clearance to back in. I will certainly install one on my next truck.
Of the many hitch receivers I have purchased, the front mounted ones have never failed to surprise me of their usefulness! From bike racks, to carrier for coolers, to my chainsaws, gas and oil, they make it work. Recently while cutting wood for a hunting lease engagement, I put a second ball on the front and used it to drive a 16' trailer up a hill to get the wood where it was needed for offloading. Backing it up had resulting in damaged trucks, trailers and numerous attempts. Using the front hitch it was a one and done deal! Love it! I have even used it to pull trees over when felling. I don't have enough fingers and toes to count the uses! If you have ever thought about it, just stop and order! You won't regret it!
I have a 2006 Silverado 2wd LD truck and mounted a curt front trailer hitch ... I mounted both side plates first without tighten down.. I then mounted the 2" receiver section ... Tightened that down then,finished cranking down side brackets !!!!! Done !!!! However I did have to cut the backside of the tow hooks facia plastic with a jig saw no problem ... I never cut into the cup portion I just cut some of the extra plastic in the back off DONE !!!!!!!
I have had this on my 2005 Chevy Silverado for a year. I have used it to hold a Yakima bike rack once but mostly to carry a large toolbox for camping trips. Easy to install. I kept my plastic air damn on and just cut out a square hole for the hitch.
The shipping was quick. Installed easily. The hitch is visible just below the fascia at the bottom of the bumper. I had a front hitch on my previous truck (Tacoma); also from etrailer. I use the front hitch to move my travel trailer into tight spaces.
Originally, with this recent purchase, I had purchased the incorrect item. All it took was an email from the staff at etrailer. The email contained product return instructions along with an RGA#. I just returned yesterday. This extra customer service made the return process quite simple.
With all my needs regarding hitches, etc. I will always check etrailer first.
Installation extremely easy, line up holes and bolt together, that simple. No trimming required.
Purchase front hitch to park 29 FT. camper at a cramped storage facility. Dropping the camper off now is as easy as picking up the camper.
All parts well packed. Website easy to use, prices are right and easy to track shipment. Would purchase from website again.
Perfect fit, quick and easy installation. Only took 25 minutes by myself. I would highly recommend this hitch. Plan using it for bike hitch, winch, cargo platform, etc.
David
6/24/2021
Fantastic, use it all the time for hauling bikes when I tow my RV
Let first say , working with Emily was great. I had an issue with the first hitch not fitting . She helped me order a new hitch that went without a hitch , no pun intended. New hitch is installed as you can see in the picture. Installation was a snap. Already doing work. Thanks again will buy from you all again.
Anything I get from etrailer and Curt hitches always works! This front mounted hitch will be no different, providing I can put it on tomorrow if it’s not raining! I will continue to buy here!
Patrick F.
11/13/2022
Still working great as all the hitches I have purchased from Curt have done. I will be buying another for my pickup truck as well!
Trailor hitch receiver not long enuff,warn winch hits bumper. (02 chevy silverado,4 wheel drv,ext cab) had 2 make tube extention w/5/8 pin holes. Not able 2 ride around w/winch attachd, due 2 weight and length. Hav 2 take winch to place of use in bed of truk and then atach 2 mount hitch.
Jenny N.
9/30/2022
I checked and for the 2002 Chevy Silverado 1500 LD I did not have a hitch that would provide a longer receiver opening.
Ashley was very helpful, haven't mounted the hitch yet but did get under their held in place and its going to fit just fine. again thank you much , will do business with you.
My front mount hitch arrived with in days of ordering. I watched the installation instructions video on your site before receiving it and it was a very easy install. Your company deserves 5 gold stars in my book. I'm a very happy customer!!!
I can’t address the installation as the box arrived torn and some of the nuts and bolts were rattling in the box. Now I have to wait for the missing hardware. The hitch itself looks to be high quality and you would think that quality packaging would be a priority. All it would take is a heavy plastic bag wrapped in cardboard to protect the bag of hardware from ripping open in transit.
Works perfectly, easy to install,I used it yesterday to move my dump trailer through the woods to the wood shed.
Installation was a breeze and easily done with simple hand tools most guys have in the garage. I' 77 and it took a little over an hour. Looks terrific!
Good hitch, easy installation, fast shi pping.
Mark
10/30/2022
Hitch is great,but Im using it on a snow plow that has stabilizer bars that are supposed to align with the hitch crossmember. Because the hitch itself is mounted on the bottom of the crossmember, they do not align.
Product arrived a day early! Recommend this company for all your Trailer needs.
Excellent product and superior customer service. Instructions indicated it would take a professional an hour to install and a normal guy (me?) 2 hours.....well, I had it installed in an hour and five minutes and only busted one knuckle! Simple install, excellent fit, great shopping experience.
Not much of a photographer...but here are a couple pics
Alun J
Kenmore WA
fast safe shipping
Works perfectly for accessories on front of truck. I use it for a motorcycle carrier.
Product arrived in a timely manner and was the right fit.. was easier to install than I thought it was going be. Took about 45 minutes. Only gripe is that the bolts that attach to the frame of truck spin even when they are in the metal plate when tightening down. Used a pair of pliers to hold end of bolt while using wrench to tighten. Other than that, exactly what I needed.
Quality product that installed quickly and quite easily. It gets a "thumbs up" from me!
I had a Chevy dealership install the hitch. My health prevents me from work such as that now days. Installation was very easy and took just about the hour suggested on the instruction sheet. I have given the pickup to my grandson but he's not trained in a standard transmission. He will have to learn!
Ask the Experts about this Snow Plow
Do you have a question about this Snow Plow?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina D.
7/17/2023
I am sorry to see this arrived in this state. I see that our customer service department has uploaded a claim. Once this is corrected we would appreciate your updated feedback.