Part Numbers: TL44FR,TL84FR
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
Note: Not compatible with trucks with plastic bed liners.
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (185 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there. Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Mine did not fit perfectly could be my truck attachment point were off a little, I just had to get larger beefier fender washers to compensate for the difference in the mounting points, all in all I am confident in their ability to keep my Bigfoot camper in place.
Keep in mind the parameters of the application these may be different on another vehicle. Camper is a Northern lite 9-6. Vehicle Chevy 3500 LB SRW 4x4. Post install, in my opinion. I’d feel my comfortable if the ‘FastGun’ tie downs were facing opposing directions. Currently attaching to the designated anchor points all four FG’s angle from the TorkFit anchor point BACK towards the NL camper’s anchor points. This positively prevents the 3600 LB. camper from rearward movement. However FOWARD movement can and has occurred. After a necessary sudden braking event I checked my clearances and discovered that forward movement did occur. About, one inch. My NL slid far enough forward that contact was made between the vehicle and the camper. Realignment was necessary. From an Engineers perspective: the best anchorage would be achieved with the anchoring devices (FastGuns, in my case) installed in opposing directions. In the future I will be placing blocks between the camper and the front of the truck bed to eliminate any forward movement.
I normally like to use the Happijac front tie downs for my camper. They are not available at this time for a 2022 Chevrolet. I had to use the torklift for this truck. They do work and I have no complaints. The only observation would be that you must remove the turn buckle to put fuel in my truck.
Perfect fit for it's function every time. This was my second order and the instructions were clear and concise. Very solid build from the get go and no need to retorque.
I definitely recommend this company.
Even their customer service was outstanding.
Congratulations for your reliability.
From Quebec City Canada
Were fairly easy to mount, just like the front units. Only minor problem was the angle of the unit was slightly off. It allowed the arm to push up on the bottom of the fender when under tension. I loosened the bolts, cut a slot in a big fender washer and lipped it between the frame and the tiedown to angle it down some. Worked fine, gave it just enough clearence.
Pros:
1. Excellent installation process. No drilling, No welding, No hammering, and no swearing.
2. They tuck up tight; out of site (almost) when the camper is off the truck.
3. They attach to the frame. This makes for a very solid ride experience.
Cons: NONE
Great product, easy to follow instructions. etrailer was very responsive and helpful the entire purchase. I highly recommended
They have been working great on our truck for our truck camper!
They have been working great on our truck for our truck camper!
Great product, fairly easy install, directions are easily understood. The only reason this did not get 5 stars is 2 of the mounting bolts, the ones through the filler plates, are about 1/4 inch too short. After all torqueing is completed there is just barely a full nut on these 2 bolts. All other bolts have at least 3 threads protruding beyond the nut surface.
These were originally on back order but came sooner than originally promised. They installed easily with no drilling on my 2021 Chevy 3500 crew cab dually. The 4 star rating is because they were slightly high and the insert rubbed my fenders. I added a 1/2 spacer between the bed and support arm and put in longer bolts and it worked perfect (I purchased these parts myself). Overall happy with the install.
Photos show the before and after I added the spacer.
This is my third or fourth set. The reason is I buy a new truck every year or so. These are simply the best tie down for campers that money can buy. Thanks etrailer!!
Installed them on my 2020 GMC Sierra 3500HD. Easy to install, function nicely and very well built.
Kit fit well. Installation was a little tricky. Looks very solid!
Parts fit as described. Had trouble with rear tie downs and getting nut and 3" sq. plate all thru the hole. And, should include additional metal fish wires, as some had to be just pulled off and the bolt was in place. Took about 2 hours to install both front and read sets.
Great product. Easy to install and super solid to secure our truck camper. And as always, etrailer is awesome to work with. Super fast shipping and when I need to call with questions every staff person I’ve dealt with have been awesome. A true pleasure to work with.
Called and talked to Greg to verify part numbers.
This is a brand new part to fit 2020 GMC 3500hd
Dually. I had on my door step a couple days later and installed this afternoon.
Very impressed with how stout the tie downs are
Thanks
Arrived ahead of predicted time. Items exactly as described. Securely packaged. Products aligned closely with online descriptions and fitting as described by the informative videos.
Easy installation with the great instructions - functions as expected on 2021 GM 3500 DRW.
Easy installation with the great instructions - functions as expected on 2021 GM 3500 DRW.
Were fairly easy to mount. Was missing a bolt in the package but after contacting etrailer they sent a replacement right away.
Easy installation, relatively. Product has help up well on a trip cross country where we removed the camper off the truck about 30 times. Did loose a pin and that size Is difficult to find. I would suggest having two pins as a spare. Etrailer as always did quick and prompt delivery and customer service is excellent. The installation and review videos are excellent help also.
Perfect fit! I have a 2021 eagle cap 1165 and had a 2008 lance 1181 both work perfect with tie-downs
Ask the Experts about this Camper Tie-Downs
Do you have a question about this Camper Tie-Downs?
TorkLift Accessories
Fit to this rack on your 2022 Chevrolet Silverado 3500
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Chevrolet Silverado 3500 Accessories
John
8/28/2023
These Tie downs have been working as expected. 2022 Chevy 3500 Dually with running boards.