The springs you are inquiring about can be replaced with the Replacement Latch Kit part # 910003-45. I would not say that they absolutely need to be replaced as the issue you have is likely related to the bushings but it is also not a bad idea to replace them at the same time as the bushings because you will have the tow bar apart and they will be easy to access.
I have attached a list of the available replacements parts for the Roadmaster Falcon All Terrain Tow Bar part # RM-522 as well. view full answer...
The .875 inch measurement you got is an odd one. The hubs that we carry that use an # L68149 inner bearing will typically use the # L44649 outer bearing. However, this will have an inner diameter of 1.063 inches.
With that being said, you may want to double check the inside diameter and check to see if there are any numbers on the bearing. There should also be a number of the race that may help identify the bearing.
If you come up with the same size though, it may end up being something... view full answer...
We have what you need!
For EZ-Lube axles which are very common on boat trailers you want to use the Spindle Nut Kit for EZ Lube Axles part # RG05-100. This will have two nuts, washers and keepers.
For the non EZ-Lube axles use the Trailer Spindle Nut 1" part # 165686 and the Cotter Pin part # 165649. these are individual so you will want two of each to have all you need.
You can confirm these will fit on your axles by measuring your spindle and ensuring that your it has 1" threads on it. view full answer...
Thank you very much for your question. The Valterra RV Sewer Hose Carrier # A04-5094BK, has the mounting brackets and screws included in the product. We searched the description of this product and no additional mounting brackets are available.
The only replacement part we found for this item is the Replacement Cap and Saddle for Valterra Adjustable Sewer Hose Carrier # A04-0448BK view full answer...
The wiring harness you will need for your 2006 Kia Sportage is # 118401. It will plug directly into the existing wiring of your vehicle. I've attached a video of it being installed on a 2007 Sportage which is the same process as yours. view full answer...
If the powered module that comes on the Curt T-Connector # C56321 shorted out and now your trailer lights are staying on constantly then you will need to replace your wiring kit as there are no replacement circuit boards or modules. You can however use the Curt Upgraded Circuit Protected Powered Tail Light Converter # C56496 and just splice it in behind the converter box.
If you'd rather go with a whole new kit then I recommend using the Tekonsha T-One # 118698 because we have found the... view full answer...
Hitch installation hardware can be used only one time and that is probably why your old hardware was not returned to you. We do offer replacement hitch hardware kit # RHK for each hitch we sell and all of the aftermarket hitches for the 2017 Kia Sportage are shown on the linked page.
You'll note that we have both 1-1/4-inch (Class II) and 2-inch (Class III) hitches for the car and you'll want to confirm which type you have so you can select the appropriate hardware kit. Your old hitch... view full answer...
Since the Sears Sport cargo carriers were made by Thule, you can use the Replacement Key for Thule Racks and Carriers # THKEYN014 as a replacement key for you SV-20 cargo carrier. view full answer...
You can take some measurements of your spindle on your travel trailer to make sure you choose the right components. I have attached a drawing that shows where you need to measure you can check out.
The best way to find replacement parts is to locate the part number on the bearings, races, and seals as noted in the attached drawing.
If you find that the # L44649 bearing is the correct size for you and the dimensions you mentioned are what you need I recommend the Bearing Kit, part # BK1-150.... view full answer...
From the sounds of your question, it looks like you are looking for replacement end caps for your Yakima roof rack on your vehicle. If this is the case, the replacements you need depend on which model of Yakima bars you have. Here are the different end cap options:
- Replacement EndCaps for Yakima Round CrossBars (QTY 4) # Y8007026 (fits all round bars except the 86" inch long model)
- Replacement EndCaps for Yakima 86" Long CrossBars - Qty 4 # Y80159
- Replacement EndCap for Yakima HD... view full answer...
The bolt size of the Curt Trailer Hitch Receiver # C13281 hardware is HHCS,M10x1.25,30,CL10.9,YZ and the washer is S-CON,7/16,YZ. You'll need 8 bolts and eight washers.
To make it easy you can order the Replacement Hardware Kit for Trailer Hitches # RHK which will come with the correct hardware for your Curt Trailer Hitch Receiver # C13281. Above the "add to cart" button there is a "Hitch Item Number" box that you would fill in with "13281" and the "Manufacturer" box can be filled in... view full answer...
You need one of 2 kits:
- Bearing Kit # BK3-210
- Bearing Kit # BK3-200
The difference between the kits is the inner diameter of the grease seal so that's what you need to check on. The 210 kit has a 2.125" ID for the seal while the 200 kit has a 2.250" ID for the seal. view full answer...
Go To Results